GENNADIY KUZMICHYOV
KAZAKHSTAN • + Follow
Description
ARDUINO SHIELD K3NG KEYER
Expansion board for Arduino, compatible with the sketch from K3NG.
Details - https://easyeda.com/UN7FGO/SHIELD_K3NG_Keyer
Code
https://github.com/k3ng/k3ng_cw_keyer
Schematic and Layout
https://easyeda.com/UN7FGO/SHIELD_K3NG_Keyer
Nov 24,2020
4,598 views
end-flag
ARDUINO SHIELD K3NG KEYER
2 Layers PCB 70.1 x 53.5 mm FR-4, 1.6 mm, 1, HASL with lead, Blue Solder Mask, White silkscreen
ARDUINO SHIELD K3NG KEYER
4598
1
5
6.25 (2)
Published: Nov 24,2020
Standard PCB
Under the
Attribution-ShareAlike (CC BY-SA)
License.
- Comments(5)
- Likes(1)
VOTING
2 votes
- 2 USER VOTES
6.25
- YOUR VOTE 0.00 0.00
-
10design
-
10usability
-
10creativity
-
10content
10.00
-
1design
-
2usability
-
3creativity
-
4content
2.50
More by GENNADIY KUZMICHYOV
-
DUMMY LOAD 50 OHM 100+ WATT
Universal dummy load 50 Ohm uses a cooling system from processors on Socket 775.Description on Russi...
-
VFO_NANO_LCD_SI5351
The main goal of the project was to create a code that would allow a radio amateur to configure the ...
-
SMALL FREQUENCY METER
A simple frequency counter from a Czech radio amateur. Budget frequency meter up to 10 MHz. Well sui...
-
END FEED ANTENNA UN:UN
Central part for a unbalanced End-Feed antenna.Designed for use in lightweight outdoor antennas.Repe...
-
DIPOLE ANTENNA BALUN
Central part for a balanced dipole antenna.Designed for use in lightweight outdoor antennas.Descript...
-
ARDUINO SHIELD K3NG KEYER
Expansion board for Arduino, compatible with the sketch from K3NG.Details - https://easyeda.com/UN7F...
-
BLUE_PILL_BOARD
Simple programming-development board for STM32 Blue pill board.
-
AVR_PROGRAMMING_BOARD_V3
Simple AVR programming board
-
SIMPLE_AUDIO_INTERFACE
A simple interface to provide galvanic isolation between the computer and the transmitter.The projec...
-
K3NG_KEYER_PANELS_FOR_ALUMINUM_PROFILE
Replacing panels for aluminum profile housing.For aluminum profile case.. Case size 40x97x100mm or 4...
-
External panel for K3NG keyer ver.2.1
A simple electronic manipulator compatible with a sketch from K3NG.The design allows the use of an e...
-
K3NG_Keyer Version 2.1
A simple electronic manipulator compatible with a sketch from K3NG.The design allows the use of an e...
-
Simple attenuator, for QRPX
Simple attenuator, for QRPX.Allows attenuation of input power over 10 watts by 6/10/20 decibels.Atte...
-
Low current circuit tester.
A device to facilitate the work of installers of access control systems and video surveillance syste...
-
STEPPER_ATTENUATOR
A simple attenuator for an amateur radio lab.Allows you to change the signal attenuation from 1 to 8...
-
HAM DIGITA INTERFACE PC->TRX
Simple transceiver control interface, fully galvanically isolated. It is possible to switch the pola...
-
HAM DIGITAL INTERFACE PC->TRX
Simple transceiver control interface, fully galvanically isolated.The printed circuit board is made ...
-
SMA DUMMY LOAD 50 OHM
Simple SMA 2512 resistors Dummy load 50 Ohm up to 20 Watt/Description in Russian - http://radiodiy.c...
-
DUMMY LOAD 50 OHM 100+ WATT
Universal dummy load 50 Ohm uses a cooling system from processors on Socket 775.Description on Russi...
-
VFO_NANO_LCD_SI5351
The main goal of the project was to create a code that would allow a radio amateur to configure the ...
-
SMALL FREQUENCY METER
A simple frequency counter from a Czech radio amateur. Budget frequency meter up to 10 MHz. Well sui...
-
END FEED ANTENNA UN:UN
Central part for a unbalanced End-Feed antenna.Designed for use in lightweight outdoor antennas.Repe...
-
DIPOLE ANTENNA BALUN
Central part for a balanced dipole antenna.Designed for use in lightweight outdoor antennas.Descript...
-
ARDUINO SHIELD K3NG KEYER
Expansion board for Arduino, compatible with the sketch from K3NG.Details - https://easyeda.com/UN7F...
-
BLUE_PILL_BOARD
Simple programming-development board for STM32 Blue pill board.
-
AVR_PROGRAMMING_BOARD_V3
Simple AVR programming board
-
SIMPLE_AUDIO_INTERFACE
A simple interface to provide galvanic isolation between the computer and the transmitter.The projec...
-
K3NG_KEYER_PANELS_FOR_ALUMINUM_PROFILE
Replacing panels for aluminum profile housing.For aluminum profile case.. Case size 40x97x100mm or 4...
-
External panel for K3NG keyer ver.2.1
A simple electronic manipulator compatible with a sketch from K3NG.The design allows the use of an e...
-
K3NG_Keyer Version 2.1
A simple electronic manipulator compatible with a sketch from K3NG.The design allows the use of an e...
You may also like
-
Choose the right brightness for your LEDs. LED RESISTANCE HELPER Tool
192 0 3 -
-
-
Ender 3 Linear Rail Upgrade (No modifying of existing parts)
450 0 0
Thank you very much for such an assessment of my work! 73!
Thank you for your interest in my project. A link to the Sketch for this version of the electronic key is available in the instructions, on the last page. If the link is not found, then you can take it from here - http://radiodiy.club/files/K3NG_SHIELD_V2.zip Sincerely, Gennady.