Fun and scalable geek handheld
The core configuration
1. STM32F030CCT6 MCU, with 256K FLASH, enough space
2. 0.96 inch OLED screen, SPI interface.
3. MICRO SD card, SPI interface
4. CH340E USB to serial chip, easy debugging
5. 24C04 EEPROM, key data storage
6. Lithium battery management, automatically switch power
7. Audio power amplifier chip with simple mixing circuit
8. Reserve extra IO and communication interface for easy expansion
Based on the above hardware,
we can DIY a lot of interesting things,
for example as follows
1. Game console, not much to say about this
2. Smart car control panel
3. Internet of Things Control Panel
4. More ways to play, to be discovered
Fun and scalable geek handheld
*PCBWay community is a sharing platform. We are not responsible for any design issues and parameter issues (board thickness, surface finish, etc.) you choose.
- Comments(0)
- Likes(7)
- 1 USER VOTES
- YOUR VOTE 0.00 0.00
-
10design
-
10usability
-
10creativity
-
10content
More by Oleg Oleg
-
Development Board STM32F103RET6
Development Board Series STM32F103RET6Resources on the board3.3/5.0/12V power input/output pinReset ...
-
DAPLINK and STM32 minimum system combination
DAPLINK and STM32 minimum system combination, one data cable can complete the download and debugging...
-
USB to RS232
This is a program verification board. The main verification content is the function of USB to RS232 ...
-
ESP Air Burner
The ESP downloader with Air Burnner interface uses probes instead of DuPont cables.
-
Docking station USB3.1
Using GL3520 USB 3.1 HUB chip,Supports super high speed, high speed and full speed USB connection, f...
-
RX5808 open source receiver
5.8g open source receiver, can receive 5.8g signal, AV video signal output. Rx5808 dual-reception fu...
-
5.8G image transmission module
It can be used for AV signal audio and video wireless transmission; baby monitor; wireless camera se...
-
GRBL-ESP32
esp32s 3d is suitable for GRBL and marlin software
-
STM32 Sensor Node
A Small STM32F103C8T6 board with all functional pins exposed. Similar to the BluePill Board except:N...
-
2.8 inch TFT touch screen
The module uses a 2.8-inch TFT color LCD screen. The module is compatible with punctual atomic 2.8TF...
-
LED dot matrix clock
LED dot matrix electronic clock based on 51 single chip microcomputer.Based on STC15W4K series ultra...
-
STM32F411Cx 401Cx minimum system + J-LINK debugger
The STM32F411 / 401 microcontroller belongs to the STM32 Dynamic Efficiency series. These devices ar...
-
Small passive DC constant current electronic load
IntroductionA small passive DC adjustable constant current (CC) electronic load with temperature-con...
-
Small jlinkV9 downloader V1.0
Adopt typec interface, stm32f205 master control, lead SWD, SWO, support virtual serial port, resista...
-
IP2325 dual string lithium battery charging module
Miniature charger for dual lithium batteries.Since the IP2325 does not have a charge balancing funct...
-
Electronic switch
The operating voltage is within 30V. Depends on the PMOS voltage.
-
Power supply module NAE20S08
Is based on SY8288A / JW5068A series power supply ic Volume: 10x10x6mm Input range: 4-23vin Output: ...
-
Solder paste dispenser
A portable miniature intelligent electric SMT solder paste dispensing pen supports quantitative extr...
-
-
Helium IoT Network Sensor Development board | H2S-Dev V1.2
91 0 0 -
-
-
-
-
3D printed Enclosure Backplate for Riden RD60xx power supplies
176 1 1
