Description
PIC 18F 28 PIN Development Board
A ZIF socket enables easy removal of the Target MCU from the development Board.
Well Marked ICSP for connecter offers easy programming of the MCU on Board.
Plug In Plug Out type crystal on the development board.
Two jumpers J1 and J2 help you Plug In Plug Out crystal from your project.
A 20 Mhz Crystal is supplied along with the kit.
Jumper J3 allows you to use RE3 as a IO pin and VPP for the ICSP connector.
A bridge rectifier (D2) takes care of any polarity connection at CN5.
Power On LED D3 displays Power on the PCB and the Voltage Regulator IC ?U2 7805 ensures regulated power to the microprocessor and other devices connected to this board.
All Port Pin Connector are capable of providing DC supply to the ADD ON cards. Please ensure that you calculate your current requirement before sourcing this supply from this PCB.
No short circuit protection is provided at these outputs.
May 30,2020
944 views
end-flag
PIC 18F 28 PIN Development Board
This is a PIC18F Development board with ICSP connector.
944
2
0
Published: May 30,2020
Download Gerber file 11
BOM(Bill of materials)
Under the
Attribution-ShareAlike (CC BY-SA)
License.
Raspberry Pi 5 7 Inch Touch Screen IPS 1024x600 HD LCD HDMI-compatible Display for RPI 4B 3B+ OPI 5 AIDA64 PC Secondary Screen（Without Speaker）
BUY NOW
ESP32-S3 4.3inch Capacitive Touch Display Development Board, 800×480, 5-point Touch, 32-bit LX7 Dual-core Processor
BUY NOW
Raspberry Pi 5 7 Inch Touch Screen IPS 1024x600 HD LCD HDMI-compatible Display for RPI 4B 3B+ OPI 5 AIDA64 PC Secondary Screen（Without Speaker）
BUY NOW
- Comments(0)
- Likes(2)
Log in to post comments.
Upload photo
0 / 10000
More by Oleg Oleg
-
Small passive DC constant current electronic load
IntroductionA small passive DC adjustable constant current (CC) electronic load with temperature-con...
-
Small jlinkV9 downloader V1.0
Adopt typec interface, stm32f205 master control, lead SWD, SWO, support virtual serial port, resista...
-
IP2325 dual string lithium battery charging module
Miniature charger for dual lithium batteries.Since the IP2325 does not have a charge balancing funct...
-
Electronic switch
The operating voltage is within 30V. Depends on the PMOS voltage.
-
Power supply module NAE20S08
Is based on SY8288A / JW5068A series power supply ic Volume: 10x10x6mm Input range: 4-23vin Output: ...
-
Solder paste dispenser
A portable miniature intelligent electric SMT solder paste dispensing pen supports quantitative extr...
-
Development Board STM32F103RET6
Development Board Series STM32F103RET6Resources on the board3.3/5.0/12V power input/output pinReset ...
-
DAPLINK and STM32 minimum system combination
DAPLINK and STM32 minimum system combination, one data cable can complete the download and debugging...
-
USB to RS232
This is a program verification board. The main verification content is the function of USB to RS232 ...
-
ESP Air Burner
The ESP downloader with Air Burnner interface uses probes instead of DuPont cables.
-
Docking station USB3.1
Using GL3520 USB 3.1 HUB chip,Supports super high speed, high speed and full speed USB connection, f...
-
RX5808 open source receiver
5.8g open source receiver, can receive 5.8g signal, AV video signal output. Rx5808 dual-reception fu...
-
5.8G image transmission module
It can be used for AV signal audio and video wireless transmission; baby monitor; wireless camera se...
-
GRBL-ESP32
esp32s 3d is suitable for GRBL and marlin software
-
STM32 Sensor Node
A Small STM32F103C8T6 board with all functional pins exposed. Similar to the BluePill Board except:N...
-
2.8 inch TFT touch screen
The module uses a 2.8-inch TFT color LCD screen. The module is compatible with punctual atomic 2.8TF...
-
LED dot matrix clock
LED dot matrix electronic clock based on 51 single chip microcomputer.Based on STC15W4K series ultra...
-
STM32F411Cx 401Cx minimum system + J-LINK debugger
The STM32F411 / 401 microcontroller belongs to the STM32 Dynamic Efficiency series. These devices ar...
-
Small passive DC constant current electronic load
IntroductionA small passive DC adjustable constant current (CC) electronic load with temperature-con...
-
Small jlinkV9 downloader V1.0
Adopt typec interface, stm32f205 master control, lead SWD, SWO, support virtual serial port, resista...
-
IP2325 dual string lithium battery charging module
Miniature charger for dual lithium batteries.Since the IP2325 does not have a charge balancing funct...
-
Electronic switch
The operating voltage is within 30V. Depends on the PMOS voltage.
-
Power supply module NAE20S08
Is based on SY8288A / JW5068A series power supply ic Volume: 10x10x6mm Input range: 4-23vin Output: ...
-
Solder paste dispenser
A portable miniature intelligent electric SMT solder paste dispensing pen supports quantitative extr...
-
Development Board STM32F103RET6
Development Board Series STM32F103RET6Resources on the board3.3/5.0/12V power input/output pinReset ...
-
DAPLINK and STM32 minimum system combination
DAPLINK and STM32 minimum system combination, one data cable can complete the download and debugging...
-
USB to RS232
This is a program verification board. The main verification content is the function of USB to RS232 ...
-
ESP Air Burner
The ESP downloader with Air Burnner interface uses probes instead of DuPont cables.
-
Docking station USB3.1
Using GL3520 USB 3.1 HUB chip,Supports super high speed, high speed and full speed USB connection, f...
-
RX5808 open source receiver
5.8g open source receiver, can receive 5.8g signal, AV video signal output. Rx5808 dual-reception fu...
You may also like
-
Modifying a Hotplate to a Reflow Solder Station
179 0 2 -
MPL3115A2 Barometric Pressure, Altitude, and Temperature Sensor
137 0 1 -
-
-
V2 Commodore AMIGA USB-C Power Sink Delivery High Efficiency Supply Triple Output 5V ±12V OLED display ATARI compatible shark 100W
387 4 1 -
How to measure weight with Load Cell and HX711
425 0 3 -
-
Instrumentation Input, high impedance with 16 bit 1MSPS ADC for SPI
531 0 0
