GENNADIY KUZMICHYOV
KAZAKHSTAN • + Follow
Description
STEPPER_ATTENUATOR
A simple attenuator for an amateur radio lab.
Allows you to change the signal attenuation from 1 to 81 decibels.
Jan 24,2022
1,055 views
STEPPER_ATTENUATOR
2 Layers PCB 26.7 x 91.4 mm FR-4, 1.6 mm, 1, HASL with lead, White Solder Mask, Black silkscreen
A simple attenuator for an amateur radio lab.
1055
3
0
Published: Jan 24,2022
PCBWay Donate 10% cost To Author
*PCBWay community is a sharing platform. We are not responsible for any design issues and parameter issues (board thickness, surface finish, etc.) you choose.
Under the
Attribution-ShareAlike (CC BY-SA)
License.
Topic
- Comments(0)
- Likes(3)
Upload photo
You can only upload 5 files in total. Each file cannot exceed 2MB. Supports JPG, JPEG, GIF, PNG, BMP
0 / 10000
More by GENNADIY KUZMICHYOV
-
BLUE_PILL_BOARD
Simple programming-development board for STM32 Blue pill board.
-
AVR_PROGRAMMING_BOARD_V3
Simple AVR programming board
-
SIMPLE_AUDIO_INTERFACE
A simple interface to provide galvanic isolation between the computer and the transmitter.The projec...
-
K3NG_KEYER_PANELS_FOR_ALUMINUM_PROFILE
Replacing panels for aluminum profile housing.For aluminum profile case.. Case size 40x97x100mm or 4...
-
External panel for K3NG keyer ver.2.1
A simple electronic manipulator compatible with a sketch from K3NG.The design allows the use of an e...
-
K3NG_Keyer Version 2.1
A simple electronic manipulator compatible with a sketch from K3NG.The design allows the use of an e...
-
Simple attenuator, for QRPX
Simple attenuator, for QRPX.Allows attenuation of input power over 10 watts by 6/10/20 decibels.Atte...
-
Low current circuit tester.
A device to facilitate the work of installers of access control systems and video surveillance syste...
-
STEPPER_ATTENUATOR
A simple attenuator for an amateur radio lab.Allows you to change the signal attenuation from 1 to 8...
-
HAM DIGITA INTERFACE PC->TRX
Simple transceiver control interface, fully galvanically isolated. It is possible to switch the pola...
-
HAM DIGITAL INTERFACE PC->TRX
Simple transceiver control interface, fully galvanically isolated.The printed circuit board is made ...
-
SMA DUMMY LOAD 50 OHM
Simple SMA 2512 resistors Dummy load 50 Ohm up to 20 Watt/Description in Russian - http://radiodiy.c...
-
DUMMY LOAD 50 OHM 100+ WATT
Universal dummy load 50 Ohm uses a cooling system from processors on Socket 775.Description on Russi...
-
VFO_NANO_LCD_SI5351
The main goal of the project was to create a code that would allow a radio amateur to configure the ...
-
SMALL FREQUENCY METER
A simple frequency counter from a Czech radio amateur. Budget frequency meter up to 10 MHz. Well sui...
-
END FEED ANTENNA UN:UN
Central part for a unbalanced End-Feed antenna.Designed for use in lightweight outdoor antennas.Repe...
-
DIPOLE ANTENNA BALUN
Central part for a balanced dipole antenna.Designed for use in lightweight outdoor antennas.Descript...
-
ARDUINO SHIELD K3NG KEYER
Expansion board for Arduino, compatible with the sketch from K3NG.Details - https://easyeda.com/UN7F...
You may also like
-
-
Helium IoT Network Sensor Development board | H2S-Dev V1.2
120 0 0 -
-
-
-
-
3D printed Enclosure Backplate for Riden RD60xx power supplies
183 1 1
