GENNADIY KUZMICHYOV
KAZAKHSTAN • + Follow
Description
Simple attenuator, for QRPX
Simple attenuator, for QRPX.
Allows attenuation of input power over 10 watts by 6/10/20 decibels.
Attenuation can add up, reaching a maximum value of 36 decibels.
Resistors can be set based on the expected power input.
Both BNC and SMA type connectors can be installed on the printed circuit board.
Feb 02,2022
913 views
Simple attenuator, for QRPX
2 Layers PCB 55.9 x 94 mm FR-4, 1.6 mm, 1, HASL with lead, Red Solder Mask, White silkscreen
Simple attenuator, for QRPX.
Allows attenuation of input power over 10 watts by 6/10/20 decibels.
913
3
0
Published: Feb 02,2022
Download Gerber file 14
PCBWay Donate 10% cost To Author
*PCBWay community is a sharing platform. We are not responsible for any design issues and parameter issues (board thickness, surface finish, etc.) you choose.
Under the
Attribution-ShareAlike (CC BY-SA)
License.
- Comments(0)
- Likes(3)
Upload photo
You can only upload 5 files in total. Each file cannot exceed 2MB. Supports JPG, JPEG, GIF, PNG, BMP
0 / 10000
More by GENNADIY KUZMICHYOV
-
BLUE_PILL_BOARD
Simple programming-development board for STM32 Blue pill board.
-
AVR_PROGRAMMING_BOARD_V3
Simple AVR programming board
-
SIMPLE_AUDIO_INTERFACE
A simple interface to provide galvanic isolation between the computer and the transmitter.The projec...
-
K3NG_KEYER_PANELS_FOR_ALUMINUM_PROFILE
Replacing panels for aluminum profile housing.For aluminum profile case.. Case size 40x97x100mm or 4...
-
External panel for K3NG keyer ver.2.1
A simple electronic manipulator compatible with a sketch from K3NG.The design allows the use of an e...
-
K3NG_Keyer Version 2.1
A simple electronic manipulator compatible with a sketch from K3NG.The design allows the use of an e...
-
Simple attenuator, for QRPX
Simple attenuator, for QRPX.Allows attenuation of input power over 10 watts by 6/10/20 decibels.Atte...
-
Low current circuit tester.
A device to facilitate the work of installers of access control systems and video surveillance syste...
-
STEPPER_ATTENUATOR
A simple attenuator for an amateur radio lab.Allows you to change the signal attenuation from 1 to 8...
-
HAM DIGITA INTERFACE PC->TRX
Simple transceiver control interface, fully galvanically isolated. It is possible to switch the pola...
-
HAM DIGITAL INTERFACE PC->TRX
Simple transceiver control interface, fully galvanically isolated.The printed circuit board is made ...
-
SMA DUMMY LOAD 50 OHM
Simple SMA 2512 resistors Dummy load 50 Ohm up to 20 Watt/Description in Russian - http://radiodiy.c...
-
DUMMY LOAD 50 OHM 100+ WATT
Universal dummy load 50 Ohm uses a cooling system from processors on Socket 775.Description on Russi...
-
VFO_NANO_LCD_SI5351
The main goal of the project was to create a code that would allow a radio amateur to configure the ...
-
SMALL FREQUENCY METER
A simple frequency counter from a Czech radio amateur. Budget frequency meter up to 10 MHz. Well sui...
-
END FEED ANTENNA UN:UN
Central part for a unbalanced End-Feed antenna.Designed for use in lightweight outdoor antennas.Repe...
-
DIPOLE ANTENNA BALUN
Central part for a balanced dipole antenna.Designed for use in lightweight outdoor antennas.Descript...
-
ARDUINO SHIELD K3NG KEYER
Expansion board for Arduino, compatible with the sketch from K3NG.Details - https://easyeda.com/UN7F...
You may also like
-
-
-
-
-
3D printed Enclosure Backplate for Riden RD60xx power supplies
156 1 1 -
-
