Gadget Reboot
CANADA • + Follow
Tools, APP Software Used etc.
|
KiCADKicad
|
Description
PIR Motion Activated Relay
A PIR motion sensor module is used with this PCB to turn on a relay when motion is detected and the ambient light is not very bright.
One use for this is to control a light to automatically turn on when someone enters a dark room.
Code
Sketch
https://github.com/GadgetReboot/PIR_Relay/
Schematic and Layout
Design files
https://github.com/GadgetReboot/PIR_Relay/
Dec 21,2022
754 views
PIR Motion Activated Relay
Automatically turn on a night light using a relay when motion is detected in a dark room
754
1
0
Published: Dec 21,2022
Download Gerber file 4
BOM(Bill of materials)
PCBWay Donate 10% cost To Author
Only PCB
PCB+Assembly
*PCBWay community is a sharing platform. We are not responsible for any design issues and parameter issues (board thickness, surface finish, etc.) you choose.
Under the
Attribution-ShareAlike (CC BY-SA)
License.
- Comments(0)
- Likes(1)
Upload photo
You can only upload 5 files in total. Each file cannot exceed 2MB. Supports JPG, JPEG, GIF, PNG, BMP
0 / 10000
More by Gadget Reboot
-
40 Pin Cable ESP32-C3 based Test Platform
This is a test platform with 40 inputs and 40 outputs, using an ESP32-C3 Super Mini module with five...
-
Serial UPDI Programmer
USB Serial to UPDI programming board for Atmel devices in the Arduino IDEHas a 5v / 3.3v switch to c...
-
Op Amp Buffer with In/Out Guitar Jacks
The pcb has a guitar input and output jack to easily connect to a breadboard for guitar effect circu...
-
16 Channel Audio Loop Switcher
This is a 16 channel audio loop switcher with 16 inputs and 16 outputs.Analog signals within a +/- 5...
-
16 Switches to RS485 Output Commands
Up to 16 switches or 5v/gnd logic inputs can be monitored and when asserted (input = gnd), a sketch ...
-
MCP42100 Digital Pot Breakout PCB
This breakout board for the MCP42100 dual digital pot has headers that are spaced for breadboard com...
-
Power Supply DC Jack/Screw Term/0.1" Header Breakout with PTC
This breakout board allows connecting a power source via 2.1x5.5mm DC jack, 7.62mm screw terminals, ...
-
16x16 Analog Switch
This 16x16 analog crosspoint switch uses two MT8816 8x16 switch ICs cascaded for a larger matrix.The...
-
Line Level Stereo Input to 3 Stereo Output Sharing PCB
This audio sharing board will take a stereo line input from a 3.5mm jack, buffer it and send it out ...
-
MIDI Breakout In/Out/Thru
This MIDI breakout board has 5 pin DIN jacks and Type A configured 3.5mm TRS jacks for Midi In, Midi...
-
Tandy CoCo Joystick Adapter - Use Digital Inputs for Analog X,Y axis
Use 5v/GND digital signals to control the analog joystick input of a Tandy Color Computer.When input...
-
Capacitor Bank Switch Box
Capacitor Breakout BoardUse dip switches to put capacitors in parallel in 1nF increments from 1 nF t...
-
Op Amp Twin T Percussion PCB
This is an op amp percussion sound generator based on the Forrest Mims circuit in books such as Gett...
-
1/4 Inch TRS Phone Jack Breakout PCB
This 1/4 inch phone jack TRS breakout board has a 6 pin header forTip, Ring, Sleeve, Switched Tip, R...
-
NPN Transistor Breakout Board
This board can be assembled with machine pin sockets to allow swapping NPN transistors as well as co...
-
GPIO Addressable LED Indicators
This pcb can read 8 digital inputs and display their high/low state on one of 8 addressable LEDs as ...
-
Guitar Stomp Switch and LED Breakout Board
This PCB takes a 9 pin 3PDT guitar effect on/off stomp switch along with an LED and resistor, and pr...
-
HV5222 Breakout Board
HV5222 32 bit high voltage shift register breakout boardThe driver chip has open drain outputs that ...
You may also like
-
-
-
-
-
3D printed Enclosure Backplate for Riden RD60xx power supplies
154 1 1 -
-
