An expanding demand for such items as smart labels, mobile phone antennas, and disposable biosensors is driving a booming market for printed electronics. It’s a market that seems destined to grow as t...
Karen Lin
Feb 22,2014
950 views
Materials characterization and device design to application development and full-system prototyping. The market for flexible, printed, and organic large-area electronics is rapidly growing. Currently...
Karen Lin
Feb 22,2014
1371 views
As the need to build smaller, lighter electronics continues, rigid flexible and flexible cable assembly technologies have been used to produce a wide range of electronic products including handheld co...
Karen Lin
Feb 21,2014
5536 views
A printed circuit board (pcb) mechanically supports and electrically connects electronic components using conductive tracks, pads and other features etched from copper sheets laminated onto a non-cond...
Karen Lin
Feb 21,2014
2723 views
A PCB board consists of multiple layers of copper separated by layers of insulating FR4 fire-resistant epoxy. A trace is a wire on a layer of the board. A via is a copper-plated hole that goes through...
Karen Lin
Feb 21,2014
1424 views
Antenna Point: PCB The point where antenna is connected is called antenna point. It is normally located at the top of the PCB of a mobile phone.Network Section: The section below antenna point and abo...
Karen Lin
Feb 21,2014
6058 views
A simple light-emitting diode PCB circuit is an excellent first project in electronics, as it illustrates the use of electrical current and gives you practical experience handling components. The circ...
Karen Lin
Feb 21,2014
3951 views
To make your own PCB LED light bulb, you will need a soldering iron and some solder, some LEDs and a pre-drilled circuit board. You will also need an old, burnt out incandescent light bulb. To make a ...
Karen Lin
Feb 21,2014
1026 views
You may have multiple mechanical PCB layers, but you will need at least one to fabricate your board. The most basic mechanical layer (sometimes referred to as Mechanical 1) outlines the physical dime...
Karen Lin
Feb 21,2014
4532 views
Power and ground planes PCB can be modified such that they contain multiple copper sections connected to different potentials. These further enhance the convenience of planes – consider a plane that ...
Karen Lin
Feb 21,2014
1424 views
If you send a pcb design to be manufactured (to a "UL-approved" fabricator) with no materials specified at all, you should still receive an acceptable board for most applications. In other words, even...
Karen Lin
Feb 21,2014
2513 views
Printed circuit boards can be as simple as a single routing layer with a mechanical layer PCB defining the physical dimensions of your board or as complicated as a multilayer board with all the layers...
Karen Lin
Feb 21,2014
1428 views
What is it about PCB's that make them such an interesting piece of engineering? The answer isn't simple and the fun isn't in the documentation it has to be said, but then it never is, but as most PCB...
Karen Lin
Feb 20,2014
1111 views
A printed circuit board (pcb) mechanically supports and electrically connects electronic components using conductive tracks, pads and other features etched from copper sheets laminated onto a non-cond...
Karen Lin
Feb 20,2014
4422 views
Pcb circuit board industry technology development process, a clear trend reflow technology. Cartridge principle of traditional reflow process can also be used , which is commonly referred to through-h...
PCBWay
Feb 20,2014
1186 views
Circuit boards are made PCB with copper conductors separated by insulating materials which are typically resin systems with a reinforcement material to add strength and stability. The most prevalent m...
Karen Lin
Feb 20,2014
2823 views
If you’ve ever seen a PCB you are no doubt familiar with their oddly green coloring. This thin green protective covering on the top and bottom of a PCB is called the solder mask and it helps protect ...
Karen Lin
Feb 20,2014
2559 views
Routing layers are used for component interconnects. These are the layers that designers spend the majority of their time perfecting. Routing layers can be located on both outer (referred to as top ...
Karen Lin
Feb 20,2014
1745 views
Introduction PCB is in English (printed circuit board) PCB for short. Usually on the insulating material , according to predetermined design , made of printed circuits, printing member ...
PCBWay
Feb 20,2014
2196 views
We will now route the board using both sides like many commercial PCBs. Having said that, use a single side wherever possible if your PCB is made using an old-fashioned process. Many problems occur wi...
Karen Lin
Feb 20,2014
1231 views
| Ranking | Name | Answers |
|---|---|---|
| 1 | PCBWay Team | 8 |
| 2 | Engineer | 1 |
| 3 | Ross Feng | 1 |
| 4 | Engineer | 1 |
