With the increasing complexity and high-speed circuit design , how to ensure that the various signals ( especially high-speed signal ) integrity , which is to ensure signal quality , become a problem ...
PCBWay
Feb 18,2014
3095 views
Electronic circuits in PCB school and in industry are normally produced through the use of PCBs (Printed Circuit Boards). The boards are made from glass reinforced plastic with copper tracks in the pl...
Karen Lin
Feb 18,2014
1112 views
Here is the newest version of PCBWay Multi-layer laminated structure.A printed circuit board (pcb) mechanically supports and electrically connects electronic components using conductive tracks, pads a...
PCBWay
Feb 17,2014
10197 views
A printed circuit board (pcb) mechanically supports and electrically connects electronic components using conductive tracks, pads and other features etched from copper sheets laminated onto a non-cond...
Karen Lin
Feb 17,2014
1689 views
Step 1: Preparing the PCBCheck to be sure the pad size of the PCB lines up with the pins on the SMD2. Clean the PCB of any dust or debris.3. Turn the soldering iron on now, and set the temperature bet...
Karen Lin
Feb 17,2014
1193 views
One effect of the growing complexity of electronic systems has been the need for greater packing densities in printed circuit assemblies. Conventional PCB assemblies that use leaded components inserte...
Karen Lin
Feb 17,2014
1089 views
Soldering surface mount components isn’t difficult, but it will require a good eye, a steady hand and a soldering iron with a small and clean tip. In a proper joint, you want the solder to adhere to b...
Karen Lin
Feb 17,2014
884 views
Through-Hole soldering is fast, fun and easy. The parts you populate your PCB’s with are the very same ones you can pull from your breadboard once your project is finished, and you are ready to make T...
Karen Lin
Feb 17,2014
1680 views
There is an enormous amount of work that goes into designing the small circuit boards that runs everything from your computer to that funny little electronic toy that talks to you. The technology behi...
Karen Lin
Feb 17,2014
1115 views
There are a few hard and fast rules when it comes to designing printed circuit boards. There are four main areas of concern: Pads, Obstacles, Text, and Origins. Even with the best auto layout software...
Karen Lin
Feb 17,2014
1640 views
Have you heard the name PCB? I guess you already have. The abbreviation of printed circuit board is PCB. It may be defined as the component that is made by combining several layers of insulating mater...
Karen Lin
Feb 17,2014
955 views
PCB designers are continuously coping with the increasing complexity of printed circuit boards or PCBs. However, the design cycles for these printed boards have also become shorter and more predictabl...
Karen Lin
Feb 17,2014
1215 views
A flexible (Flexible Printed circuit board) is a polyimide or polyester film as a base material having a high reliability , excellent flexible printed circuit . Early flexible PCB is limited to the c...
PCBWay
Feb 17,2014
1855 views
PCB design is a very broad technology involves a lot of factors that affect the design results . This article first put aside other factors , it is only about a few aspects of PCB design experience, f...
PCBWay
Feb 17,2014
1291 views
Topology refers to the alignment order of the wiring and the wiring structure of a network. For multi- network load , according to the actual situation, select the appropriate cabling topologies and t...
PCBWay
Feb 17,2014
6020 views
In the circuit design can be exposed to a variety of occasions this term transmission line . Obviously , the transmission line is one of the elements which emphasis on the signal integrity analysis , ...
PCBWay
Feb 17,2014
1908 views
( 1 ) monorail (Single Lane) Monorail -type transport mechanism shown in Figure 1 . Figure 1 Schematic monorail conveyor mechanism A monorail -type transport mechanism to send a board. When a boa...
PCBWay
Feb 17,2014
1024 views
1 - General rules 1.1 PCB board pre- division digital, analog , DAA (data access arrangement, data access means ) the signal wiring region . 1.2 digital, analog components and the corresponding trac...
PCBWay
Feb 17,2014
681 views
The designer may design an odd layer printed circuit board (PCB). If no additional wiring layer , why use it? Do not allow the board to reduce the layer thinner it? If the board is at least one layer ...
PCBWay
Feb 17,2014
1104 views
1, Usually a photosensitive shortening much heat type solid white oil light, first confirm whether you use white oil for thermosetting type white oil. 2, yellow reason please confirm oven temperature...
PCBWay
Feb 17,2014
994 views
| Ranking | Name | Answers |
|---|---|---|
| 1 | PCBWay Team | 6 |
| 2 | Engineer | 1 |
| 3 | Stephen Newport | 1 |
