EdgePro 1 is a tiny open source development platform with state of the art firmware based on a POSIX compliant Real Time Operating System. Its main advantage is to take full use of the LuaJIT interpre...
PCBWay
Aug 19,2022
1781 views
When doing 3D printing, we usually don't choose solid infill, so the density of the infill has a big impact on the printed part. When less infill material is used, so does the time and cost of printin...
PCBWay
Aug 19,2022
10842 views
In the previous steps, we have completed the creation of all the inner layer circuits and the required holes (Through/Buried/Blind holes). Next, we have to enter the outer layer imaging process of the...
PCBWay
Aug 15,2022
4327 views
DeepDeck, combined with 16 RGB, mechanical keys and two RGB rotary encoders with push buttons, is a wireless, fully programmable and open source macropad. It can connect to your devices via Bluetooth,...
PCBWay
Aug 12,2022
2249 views
Two ways to share PCB projects:1.Enter PCBWay community (https://www.pcbway.com/project/shareproject/) and find the Create a project button.2.Once upload a PCB file in our website, there will be a Sha...
PCBWay
Aug 12,2022
6257 views
As the electronic products become thinner and smaller, the thickness and volume of PCB installed in these devices are smaller, which promotes the gradual maturity of HDI technology, resulting in ultra...
PCBWay
Aug 10,2022
2589 views
The hole walls after drilling are composed of non-conductive epoxy resin and fiberglass board. In order to connect circuits between different layers, it is necessary to metalize the hole walls through...
PCBWay
Aug 08,2022
3822 views
Since PCBWay moved to the new factory, after a year of adjustment, our production capacity and efficiency have been greatly improved. In order to give back to our customers for their support, we decid...
Anson Bao
Aug 05,2022
11748 views
HistorySLS ( Selective Laser Sintering ) is one of the earliest 3D printing technologies. Nowadays, the two most common powder bed fusion systems are plastic based, which is called SLS.PrincipleThe SL...
PCBWay
Aug 05,2022
3776 views
Aper-Oculus is a carrier board for Xilinx's Kria SOM and can provide compact and modular solutions for those with high-speed digital design. This board has a plethora of I/D, including FMC, MPI and a ...
PCBWay
Aug 05,2022
2073 views
To make the circuit of each layer connected, the boards need to go through the drilling process to make the corresponding holes according to the specifications in the drill files. For single and doubl...
PCBWay
Aug 01,2022
3934 views
By Hesam Moshiri, Anson BaoDisclaimer: Some parts of this circuit carry dangerous Mains voltage. Be careful with your experiments. If you are a beginner, ask some experienced users to guide you. ...
Anson Bao
Aug 01,2022
18946 views
Green used to be thought of as the typical PCB colour. The availability of various PCB colours has also increased with the development of technology and more inventiveness.Every patched circuit is bui...
PCBWay
Jul 29,2022
12577 views
Loko is battery operated GPS tracker that can send navigation data to its receiver via peer-to-peer LoRa radio. Based on radio communication, Loko doesn’t require a sim-card or monthly fee. It can wor...
PCBWay
Jul 29,2022
1926 views
Prior to lamination, the surface of inner image layer needs to go through an oxide process (brown oxide or black oxide treatment) to roughen and passivate the copper surface, increase the interaction ...
PCBWay
Jul 22,2022
4363 views
VXSDR-20 is a microwave software defined radio that has the ability to transmit and receives from 5 to 20GHz at 160 million samples per second. It has capabilities which are similar to other high-end ...
PCBWay
Jul 22,2022
1716 views
1.ABSABS is one of the most common thermoplastic materials with good mechanical property, excellent impact strength, high heat resistance and good machinability.ABS has a low density and is ideal for ...
PCBWay
Jul 22,2022
4443 views
Surface Pre-TreatmentThe copper sheet after cutting has oxides, grease and other impurities attached to the surface, which firstly needs to be pretreated. The main purpose of pretreatment is to remove...
PCBWay
Jul 19,2022
3644 views
Correction of the bent nylon pieceThe first step is to heat the side that needs to be repaired, soften it for correction.The second step is to take a heavy object and place it on the curved surface, c...
PCBWay
Jul 15,2022
2860 views
Pixel Pump is an open source vacuum pump for manual SMT assembly with a pen, a foot pedal, RGB LED buttons and a variety of functions that can make the process interesting. It is suitable for both ind...
PCBWay
Jul 15,2022
2747 views
| Ranking | Name | Answers |
|---|---|---|
| 1 | PCBWay Team | 6 |
| 2 | Engineer | 1 |
| 3 | Stephen Newport | 1 |
