Fabio Battaglia
ITALY • + Follow
Description
Angled 44 pin 2.0mm pitch adapter
I was in need of fitting a uSD to IDE adapter inside a cramped case, the connector for it was horizontal, but the only space left was in the vertical direction. So I made this adapter.
Fundamentally, it is meant to angle a 2x22 pin, 2.0mm pitch connector by 90 degrees.
Schematic and Layout
https://github.com/hkzlab/ide44_angled
Feb 16,2025
84 views
end-flag
Angled 44 pin 2.0mm pitch adapter
Fundamentally, it is meant to angle a 2x22 pin, 2.0mm pitch connector by 90 degrees,
84
0
0
Published: Feb 16,2025
Download Gerber file 0
PCBWay Donate 10% cost To Author
*PCBWay community is a sharing platform. We are not responsible for any design issues and parameter issues (board thickness, surface finish, etc.) you choose.
Under the
Attribution-ShareAlike (CC BY-SA)
License.
Raspberry Pi 5 7 Inch Touch Screen IPS 1024x600 HD LCD HDMI-compatible Display for RPI 4B 3B+ OPI 5 AIDA64 PC Secondary Screen（Without Speaker）
BUY NOW
ESP32-S3 4.3inch Capacitive Touch Display Development Board, 800×480, 5-point Touch, 32-bit LX7 Dual-core Processor
BUY NOW
Raspberry Pi 5 7 Inch Touch Screen IPS 1024x600 HD LCD HDMI-compatible Display for RPI 4B 3B+ OPI 5 AIDA64 PC Secondary Screen（Without Speaker）
BUY NOW
- Comments(0)
- Likes(0)
Log in to post comments.
Upload photo
0 / 10000
More by Fabio Battaglia
-
8x8 LED MATRIX EDUBOARD
This board is an educational implementation of an 8x8 multiplexed led matrix. The rows/columns bits ...
-
dupico - EPROM_01 POD
The EPROM_01 POD is an adapter for the DuPAL V3 (AKA "dupico") meant to support the most common 24/2...
-
MSP-MDC Redux
This board is a reverse-engineered recreation of the CPU/Security module for the Wink arcade game (1...
-
dupico - PAL POD
The PAL POD is an adapter for the DuPAL V3 (AKA "dupico") meant to support 20 and 24 pin PAL (and pi...
-
DuPAL V3 - dupico
The DuPAL V3, AKA "dupico" board is a simple circuit that mounts a Raspberry Pico (RP2040), 74HC595 ...
-
SCART SyncSplitter
This card takes an RGB + Composite signal from a SCART connector and outputs the same RGB signal + s...
-
PlayStation PU-22 8MB RAM daughterboard
This daughterboard replaces the RAM IC on PU-22 PlayStation motherboards, allowing the user to expan...
-
The Padapter
This board converts a SEGA MegaDrive/Genesis 3-button gamepad for C64 (and similar)/Amiga use.All bu...
-
Commodore C128 (310381 R7) SRAM Adapter
This board implements a static RAM replacement for the DRAMs on a C128 with a 310381R7 motherboard.Y...
-
Angled 44 pin 2.0mm pitch adapter
I was in need of fitting a uSD to IDE adapter inside a cramped case, the connector for it was horizo...
-
Lava RSC Lite Famiclone Upgrade board
The Lava RSC is a family of very nice Famiclones that use ICs found in the original Famicom, complem...
-
A500 IDE LED mod board
This board reproduces the same circuit that the A500 uses to flash the "DRIVE" LED when the /MTR0 si...
-
C64 250407 SRAM Adapter
This board implements a static RAM replacement for the DRAMs on a C64 with a 250407 motherboard. I w...
-
8x8 LED MATRIX EDUBOARD
This board is an educational implementation of an 8x8 multiplexed led matrix. The rows/columns bits ...
-
dupico - EPROM_01 POD
The EPROM_01 POD is an adapter for the DuPAL V3 (AKA "dupico") meant to support the most common 24/2...
-
MSP-MDC Redux
This board is a reverse-engineered recreation of the CPU/Security module for the Wink arcade game (1...
-
dupico - PAL POD
The PAL POD is an adapter for the DuPAL V3 (AKA "dupico") meant to support 20 and 24 pin PAL (and pi...
-
DuPAL V3 - dupico
The DuPAL V3, AKA "dupico" board is a simple circuit that mounts a Raspberry Pico (RP2040), 74HC595 ...
-
SCART SyncSplitter
This card takes an RGB + Composite signal from a SCART connector and outputs the same RGB signal + s...
-
PlayStation PU-22 8MB RAM daughterboard
This daughterboard replaces the RAM IC on PU-22 PlayStation motherboards, allowing the user to expan...
-
The Padapter
This board converts a SEGA MegaDrive/Genesis 3-button gamepad for C64 (and similar)/Amiga use.All bu...
-
Commodore C128 (310381 R7) SRAM Adapter
This board implements a static RAM replacement for the DRAMs on a C128 with a 310381R7 motherboard.Y...
-
Angled 44 pin 2.0mm pitch adapter
I was in need of fitting a uSD to IDE adapter inside a cramped case, the connector for it was horizo...
-
Lava RSC Lite Famiclone Upgrade board
The Lava RSC is a family of very nice Famiclones that use ICs found in the original Famicom, complem...
-
A500 IDE LED mod board
This board reproduces the same circuit that the A500 uses to flash the "DRIVE" LED when the /MTR0 si...
You may also like
-
-
-
Modifying a Hotplate to a Reflow Solder Station
578 1 5 -
MPL3115A2 Barometric Pressure, Altitude, and Temperature Sensor
336 0 1 -
-
-
V2 Commodore AMIGA USB-C Power Sink Delivery High Efficiency Supply Triple Output 5V ±12V OLED display ATARI compatible shark 100W
805 4 2 -
How to measure weight with Load Cell and HX711
577 0 3
