Narrowband FM receiver for 2-meter band
This project is about MC3362 and ADF4351 based modularized, 2-meter narrow band FM receiver. In this design, the receiver splits into three modules as RF preamplifier, MC3362 tuner, and ADF4351 oscillator. The RF preamplifier builts around BF900 dual-gate MOSFET. The tuner stage builts using the popular MC3362, low power narrowband FM receiver IC. For the oscillator, we use the ADF4351 DDS RF signal generator module.
The core component of this receiver is MC3362 IC. This IC was designed by Motorola and is no longer in production, but this IC is still available to purchase in many online stores. The chip we used in this receiver was purchased from a local electronic component store for LKR 75 (USD 0.2).
The RF preamplifier used in this receiver extracts from the N.Ganesan's (VU3GEK) LRR200, 2-meter band FM receiver project.
In this prototype, the above preamplifier was built as a module using a Manhattan construction technique. The SO-239 antenna input socket is also soldered directly to the preamplifier board. The preamplifier output connects to the input of the 1st mixer stage of MC3362 via a 50Ω coaxial link. This preamplifier is designed to operate using an 8V DC power source. If the BF900 transistor is not available, use an equivalent dual-gate, UHF range, N-channel MOSFET transistor.
The tuner stage of this receiver is a minimal version of the MC3362 circuit. This tuner module mainly consists of 10.7MHz and 455kHz ceramic filters, a 42IF301 - I.F transformer, and a 10.245MHz crystal. The local oscillator stage of this receiver is modified to use the ADF4351 RF signal generator. During the prototyping stages, we drive this module using a 5V DC power source.
For the oscillator stage, we use the ADF4351 DDS RF signal generator module. Apart from the ADF4351 signal generator, this module has an STM32F103-based driver and a TFT touch LCD. The RF output of this oscillator is directly connected to one of the local oscillator terminals of MC3362 IC. This module is designed to work with 5V. The supply voltage is feeding to the module through the onboard USB connector.
During the prototyping stages, we connect the AF output of this receiver to the TPA3001D1 power amplifier. Any AF power amplifier with 3W or higher rated output will work well with this receiver.
After connecting a suitable antenna, we were able to receive a very clear 2-meter band signal from the receiver. During the testing phase, we got extremely good reception of the RSSL VHF net at 145.625MHz (local oscillator frequency - 134.875MHz) from this receiver. For this test, we used a 5-element Yagi antenna.
Narrowband FM receiver for 2-meter band
*PCBWay community is a sharing platform. We are not responsible for any design issues and parameter issues (board thickness, surface finish, etc.) you choose.
- Comments(1)
- Likes(2)
- Tim Loyal Apr 21,2023
- Catur Sujatmiko Purnomo Aug 05,2022
- 0 USER VOTES
- YOUR VOTE 0.00 0.00
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
More by Dilshan Dilshan Ranmal Jayakody
- Echo Generator for Microphones This project is about a single-channel microphone echo generator circuit. This circuit builds around...
- Universal HD44780 LCD interface YALI (Yet Another LCD Interface) is an open-source project to provide a universal interface to drive...
- 6-channel stereo speaker selector This project is a DIY six-channel stereo speaker selector based on STC15W201 MCU. The purpose of thi...
- 5.1 channel analog audio processor In this project, we developed a 5.1-channel analog audio processor using PT2322 IC. PT2322 is an ine...
- StarPointer - virtual electronic finderscope StarPointer is a virtual electronic finderscope for astronomical telescopes. This device works with ...
- Narrowband FM receiver for 2-meter band This project is about MC3362 and ADF4351 based modularized, 2-meter narrow band FM receiver. In this...
- 5.1 channel audio preamplifier This project introduces a digitally controlled 5.1 channel audio preamplifier system. This amplifier...
- NTP based digital clock panel This project introduces an open-source, ATmega328 based, configurable NTP clock with a 2.3-inch, 7-s...
- AVR High Voltage Programmer 2 AVR-HV2 is Arduino based high voltage parallel programmer for AVR microcontrollers. This programmer ...
-
-
-
-
-
-
3D printed Enclosure Backplate for Riden RD60xx power supplies
154 1 1 -
-