OPL2LPT Replica
Original GITHUB: https://github.com/zjuyzj/OPL2LPT-Replica
Bill of Material
ComponentDesignatorQuantityNote & Possible Sources
Leaded 100pF (101) MLCCC11Mouser 594-K101J15C0GF5UH5
Leaded 100nF (104) MLCCC21Mouser 594-K104K15X7RF5UL2
Leaded 10uF Pol. Cap.C3, C5, C63Mouser 667-ECA-1EM100
Leaded 2.2uF (225) MLCCC41Mouser 81-RDER71H225K2M1H3A
Leaded 3mm Green LEDD11Mouser 630-HLMP-Y801-JPP00
74HC04 CMOS InvertersIC11Mouser 595-CD74HC04E
Yamaha YM3014B DACIC21https://www.aliexpress.com/item/32611185781.html, DIP-8 socket is recommended
Yamaha YM3812 OPL2IC31https://www.aliexpress.com/item/32595976031.html, DIP-24 socket is recommended
LM358 Dual OP AmpIC41Mouser 595-LM358AP
Leaded Mini USB Type B ConnectorP11Mouser 571-2172034-1
D-Sub 25P R/A Male ConnectorP21Mouser 523-L717SDB25P1ACH3R
Header 2P 2.54mmP3, W12Mouser 855-M20-9990246
3F07 3.5mm Stereo Audio JackP41https://www.aliexpress.com/i/32478957056.html
1k 1/4W ResistorR1, R2, R33Mouser 279-YR1B1K0CC
10k WH148 PotentiometerR41https://www.aliexpress.com/item/32998649900.html
10k 1/4W ResistorR5, R62Mouser 279-YR1B10KCC
TSW DIP-6*6*11 KeyS11https://www.aliexpress.com/item/32725384168.html
Crystal HC-49S 3.58MHzY11Mouser 449-LFXTAL032257BULK
Notes for Assembling & Testing
- 5V DC power is needed, either from Mini-USB port or external power pins
- Try to press RST SW to apply a manual reset when YM3812 behaves abnormal
- Detailed parameters for components are noted on the board's silkscreen
- Crystal must be 3.58MHz for accurate pitch of notes
- Using 74LS04 to substitute 74HC04 for the Pierce oscillator is not recommended
Note: If the oscillator doesn't work, replace the two 1k ohms resistors around the 74HC04 IC with higher value resistors such as 4.7k ohms. Fine tuning for 100pF (101) MLCC capacitor around the 74HC04 may be also needed.
OPL2LPT Replica
*PCBWay community is a sharing platform. We are not responsible for any design issues and parameter issues (board thickness, surface finish, etc.) you choose.
- Comments(0)
- Likes(1)
- Engineer Nov 07,2024
- 0 USER VOTES
- YOUR VOTE 0.00 0.00
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- Necroware S7-VRM (2024 Version) Note from PCBWay: There are some problems in the BOM on the project page that cannot be resolved. If...
- Kung Fu Flash 2 Cartridge for C64 ORIGINAL GITHUB: https://github.com/KimJorgensen/KungFuFlash2
- Pico Nes v0.2 - A RP2040 NES ORIGINAL GITHUB: https://github.com/fhoedemakers/pico-infonesPlus
- Pico Nes v2.0 - A RP2040 NES ORIGINAL GITHUB: https://github.com/fhoedemakers/pico-infonesPlus
- SDrive-Simple-II Original Website: https://ataribits.weebly.com/sdrive.html
- RAMBO XL-II Atari 256K Upgrade V 1.1 This is a clone of the original ICD RAMBO XL 256K (64+192) memory upgrade suitable for either the 80...
- OPL2LPT Replica Original GITHUB: https://github.com/zjuyzj/OPL2LPT-ReplicaBill of MaterialComponentDesignatorQuantit...
- Pico Nes v2.1 - A RP2040 NES ORIGINAL GITHUB: https://github.com/fhoedemakers/pico-infonesPlus
- Otaku-Flash Cart for Atari 2600 / 7800 & 2600+ ORIGINAL GITHUB: https://github.com/karrika/Otaku-flash
- The Ultimate Cart Atari XL / XE ORIGINAL GITHUB: https://github.com/robinhedwards/UltimateCartThis link contains the original Gerber...
- PlusCart 2600 Unified SMD PCB ORIGINAL GITHUB: https://github.com/Al-Nafuur/United-Carts-of-Atari
- Sega Mega Drive / Genesis joystick to Atari 8-bit ORIGINAL GITHUB: https://github.com/eyvind/sega-adapter
- NES Cart CNRom ORIGINAL GITHUB: https://github.com/emeargt/nes-cnromMemory Supportv02 was designed to support the S...
- Simple NES Cart (Mapper 0 Nes Cart) Original GITHUB: https://github.com/doragasu/mojo-nesNES cartridge with no mapper support. Initially...
- TS2068 Eprom Command Cartridge V2 Original Website: https://gitlab.com/NF6X_Retrocomputing/ts2068cartThis board allows many 28-pin EPR...
- ATARI 800XL 256KB XE compatible QuarterMEG Atari 800XL, XE compatible, for Ataris with C021697 (or C021698), schematics Claus Buchho...
- UNO2SIO V4 BOM:2x 4.7K THT1x 74LS07 THT
- Fujinet V1.6 for 576nuc Original Website: https://fujinetwifi.github.io/WIKI GITHUB: https://github.com/FujiNetWIFI/fujinet-...
-
-
-
-
-
-
3D printed Enclosure Backplate for Riden RD60xx power supplies
154 1 1 -
-