Dial lamp to LED conversion boards
I recently converted the dial lamps on a Sony CRF-320 receiver to LED's, and the effect was wonderful. The dial lamps were very dim, and finding suitable replacements is becoming difficult. LEDs also use far less current, so this conversion is a great idea.
The only issue I had was wiring up the simple circuit point-to-point, so I decided to make small PCBs to simplify the task. I designed two versions - a through-hole one for most of us, and an SMD version for the brave at heart.
Be sure to order them as panelised boards so that the price is more affordable. Also, you can - and should - chat with the live assistant, who can help you achieve the most affordable and practical panalisation for the quantity you requir.
Note that in some cases polarity is an issue, so watch the video.
The video link: https://youtu.be/6an87kb4WWU
Dial lamp to LED conversion boards
*PCBWay community is a sharing platform. We are not responsible for any design issues and parameter issues (board thickness, surface finish, etc.) you choose.
- Comments(0)
- Likes(2)
More by Manuel Caldeira
-
SMD version - Bluetooth Module Supply and Booster board for tube radio
The SMD version of my Tube Radio Bluetooth Module boardsThe definitive Bluetooth Module PCB to seaml...
-
Capacitor Discharger
Working with tube gear and high-end audio equipment presents certain challenges, the most significan...
-
Bridge Rectifier with Mosfet Voltage Dropper 2024-09-02
This PCB is the perfect solution to replace the selenium rectifier in vintage tube radios with moder...
-
Decade Resistor Box using inexpensive 11-position rotary switches, and 3D printed enclosure.
Decade Resistor Box built with cost-effective 11-position rotary switches, making it an affordable y...
-
Magic Eye Switch for Bluetooth Boards
Magic Eye Switch for Bluetooth BoardsThis is an add-on to allow the Bluetooth Boards that I designed...
-
Tube Radio Bluetooth Module boards
The definitive Bluetooth Module PCB to seamlessly add BT to a tube radio, with no buzzing noise, and...
-
Mini-Whip Antenna switcher with Bias-T
A self-contained antenna switcher with Bias-T for the Mini-Whip, with incorporated switching relay.
-
Capacitor Foil-Side detector
Respecting foil capacitor 'polarity' in the restoration of vintage electronics gear is a much-debate...
-
Inverse RIAA Network
This Inverse RIAA Network lets you use your normal signal generator to test phono inputs of an ampli...
-
Wax removal and alignment tool for tube radios
Wax removal and alignment tool for tube radios
-
Dial lamp to LED conversion boards
I recently converted the dial lamps on a Sony CRF-320 receiver to LED's, and the effect was wonderfu...
-
PCB_dial lamp LED boards_SMD
PCBs to convert dial lamps to LEDs on vintage radios, SMD version.
-
Sony CRF-320 replacement gear set
A set of 3 gears for the Sony crf-320 and crf-330 receivers, which are a common source of problems, ...
-
test lead rack
Cable test rack in resin
-
test lead rack
Cable test rack in PETG
-
AC and DC voltage multiplier to extend the low voltage range of analogue multimeter and increase input impedance
AC and DC voltage multiplier to extend the low voltage range of analogue multimeter and increase inp...
-
PCB_Fetzer Valve smd_2023-10-09
An SMD version of a JFET Booster/Buffer that fits inside the guitar body, creating active pickups an...
-
PCB_Fetzer Valve_2023-09-03
A Through-hole Buffer / Booster using a single JFET, that fits inside the guitar to provide active p...
-
-
Helium IoT Network Sensor Development board | H2S-Dev V1.2
90 0 0 -
-
-
-
-
3D printed Enclosure Backplate for Riden RD60xx power supplies
176 1 1
