There is an enormous amount of work that goes into designing the small circuit boards that runs everything from your computer to that funny little electronic toy that talks to you. The technology behi...
Karen Lin
Feb 17,2014
1115 views
There are a few hard and fast rules when it comes to designing printed circuit boards. There are four main areas of concern: Pads, Obstacles, Text, and Origins. Even with the best auto layout software...
Karen Lin
Feb 17,2014
1643 views
Have you heard the name PCB? I guess you already have. The abbreviation of printed circuit board is PCB. It may be defined as the component that is made by combining several layers of insulating mater...
Karen Lin
Feb 17,2014
957 views
PCB designers are continuously coping with the increasing complexity of printed circuit boards or PCBs. However, the design cycles for these printed boards have also become shorter and more predictabl...
Karen Lin
Feb 17,2014
1217 views
A flexible (Flexible Printed circuit board) is a polyimide or polyester film as a base material having a high reliability , excellent flexible printed circuit . Early flexible PCB is limited to the c...
PCBWay
Feb 17,2014
1855 views
PCB design is a very broad technology involves a lot of factors that affect the design results . This article first put aside other factors , it is only about a few aspects of PCB design experience, f...
PCBWay
Feb 17,2014
1294 views
Topology refers to the alignment order of the wiring and the wiring structure of a network. For multi- network load , according to the actual situation, select the appropriate cabling topologies and t...
PCBWay
Feb 17,2014
6026 views
In the circuit design can be exposed to a variety of occasions this term transmission line . Obviously , the transmission line is one of the elements which emphasis on the signal integrity analysis , ...
PCBWay
Feb 17,2014
1910 views
( 1 ) monorail (Single Lane) Monorail -type transport mechanism shown in Figure 1 . Figure 1 Schematic monorail conveyor mechanism A monorail -type transport mechanism to send a board. When a boa...
PCBWay
Feb 17,2014
1026 views
1 - General rules 1.1 PCB board pre- division digital, analog , DAA (data access arrangement, data access means ) the signal wiring region . 1.2 digital, analog components and the corresponding trac...
PCBWay
Feb 17,2014
683 views
The designer may design an odd layer printed circuit board (PCB). If no additional wiring layer , why use it? Do not allow the board to reduce the layer thinner it? If the board is at least one layer ...
PCBWay
Feb 17,2014
1106 views
1, Usually a photosensitive shortening much heat type solid white oil light, first confirm whether you use white oil for thermosetting type white oil. 2, yellow reason please confirm oven temperature...
PCBWay
Feb 17,2014
998 views
Method 1 of 4: Design1.Have a procedure in mind before attempting the task. Remember, a good design comes first. 2.Draw the circuit schematic on either graph paper or a simulation programs such as Mu...
Karen Lin
Feb 10,2014
2506 views
Volume and available manufacturing capabilities are two of the most important factors which affect PCB costs as well as the production of low cost yet high speed PCBs that differ when it comes to the ...
Karen Lin
Feb 10,2014
1143 views
IP or intellectual property is an organization’s valuable asset which is often developed by a design engineer’s vision of the bus structure together with its relationship with its components, while al...
Karen Lin
Feb 10,2014
1040 views
Nowadays, smaller devices are being integrated with high speed circuits as the consumers demand faster and more functional mobile devices that they can take anytime and anywhere. This has led design e...
Karen Lin
Feb 10,2014
819 views
The consistent improvement of Prototype PCB designs provides a multitude of advantages to its end users. With new generation silicon such as 45nm and 95 nm being introduced, users are provided with Pr...
Karen Lin
Feb 10,2014
1106 views
Multi-layer PCBs are circuit boards made up of more than two electrical layers (copper layers) superimposed on each other. The copper layers are bonded together by resin layers(prepreg). Multi-layer b...
Karen Lin
Feb 10,2014
1108 views
Electronic equipment is a combination of electrical and electronic components connected to produce a certain design function. printed circuit board is usually abbreviated as PCB and quite often refers...
Karen Lin
Feb 10,2014
859 views
Electronic devices have taken a prominent part of our lives. With this fact in mind, the extensive range of devices from cell-phones to servers, irrespective of their sizes and uses are now being desi...
Karen Lin
Feb 10,2014
1126 views
| Ranking | Name | Answers |
|---|---|---|
| 1 | PCBWay Team | 6 |
| 2 | Engineer | 1 |
| 3 | Stephen Newport | 1 |
