Brian K. White's Profile - Engineer - PCBWay Community

Brian K. White

Recommended

Order usingMaterial: NylonProcess: SLS (or MJF if PCBWAY starts offering it)This is the plastic carrier part used by:REX Classichttps://github.com/bkw777/REX_ClassicMolex 7880x bus taphttps://github...
Molex 7880x-28 PCB Carrier
23301
Adapter PCB and snap cover for FluxEngineProvides both a 34-pin connector for normal 3.5 inch and 5.25 inch drives, and a 50-pin connector for 8 inch drives.The fpga board may be connected with or wit...
FluxEngine Hat
39300
Re-implementation of Node Systems DATAPAC / RAMPAC.1 Megabyte ram disk for TANDY Model 102 & 200. 512k usable by RAMDSK.CO, plus another 512k only usable as raw space from self-written code.https...
MiniNDP - RAMDisk for TRS-80 Model 100/102/200
73705
Provides an on-board memory battery for the REXCPMAssembly notes:For battery holders BT1, BT2, BT3 (NOT BT4!) break the rear walls off before soldering, so that a battery can pass all the way through ...
Batteries for REXCPM
72801
REQUIRES 1.2 mm PCBWarning: The total cost for parts for this is around $100 USDThis is an "IC-Card" for TANDY WP-2.It functions the same as a battery-backed 128K SRAM, except it provides 4 128K banks...
512k MRAM IC-Card for TANDY WP-2
115301
ONLY for TRS-80 / TANDY Models 100, 102, 200Provides 4 virtual 32K EPROM from a single 128K flash chip, in a Molex 78802 form factor to fit in a Molex 78805 socket.The pinout at the castellated edge c...
M4ROM_TANDY - Writable multi option rom module for TRS-80 Model 100/102/200
133605
Programming adapter to program M4ROM_TANDY and M4ROM_27256 .Solid electrical contact with the center pins is made the fact that the receptacle holes in the center of the M4ROM boards are slightly clos...
M4ROM Programming Adapter for M4ROM_TANDY and M4ROM_27256
76801
Provides 4 virtual 32k EPROM from a single 128k flash chip, in a Molex 78802 form factor to fit in a Molex 78805 socket.The pinout at the castellated edge contacts is standard 32Kx8 parallel mask rom,...
M4ROM 27256 - Writable multi option rom module for EPSON PX-4, PX-8, TANDY 600, any Molex 78805 socket with standard pinout
77700
Tiny version of 96K ram module for TANDY 600The larger card below is the original 96K ram card for comparison. They have chips on both sides totalling 12 ram chips and 4 glue logic.The new card is en...
TANDY 600 RAM - TINY Version
93100
96K SRAM module for TANDY 600, all through-hole components version. Replaces Tandy Cat. No. 26-3910 There are other versions available, this is just the all-through-hole version. Other versions are ...
TANDY 600 RAM 96K THT
58601
https://github.com/bkw777/MounT
Teensy MounT
102701
192K SRAM for TANDY 600The original option RAM banks for TANDY 600 are 96K, and the machine can accept a maximum of 2 cards, for a total of 192K possible add-on ram plus the built-in 32K for a total o...
TANDY 600 192K DUAL RAM
60802

1 2 3 4

The PCBWay that recognize the talent and effort of the best ELECTRONIC designers in the World.

© COPYRIGHT 2019

About us
Contact us
Follow us on