AudioDIWHY
UNITED STATES OF AMERICA • + Follow
Description
2x 1J24B breakout board
The 1J24B is a Soviet era low voltage pentode, with a useful plate voltage of only 30VDC.
Its leads are fragile and hard to work with; this Breakout board allows you to easily breadboard two of them from a single +/- 10 to 15V DC power source.
Please see this blog post for more information. https://audiodiwhy.blogspot.com/2022/03/124b-pentode-dual-voltage-board-not-fun.html
Schematic and Layout
Schematic
tube timbre 2x tubes 2-8-22.sch
Board
tube timbre 2x tubes 2-8-22.brd
Mar 31,2022
915 views
2x 1J24B breakout board
Put two 1J24B low voltage pentodes on a breakout board, to assist with breadboarding!
915
0
0
Published: Mar 31,2022
Download Gerber file 8
BOM(Bill of materials)
PCBWay Donate 10% cost To Author
Only PCB
PCB+Assembly
*PCBWay community is a sharing platform. We are not responsible for any design issues and parameter issues (board thickness, surface finish, etc.) you choose.
Under the
Attribution-MIT
License.
- Comments(0)
- Likes(0)
Upload photo
You can only upload 5 files in total. Each file cannot exceed 2MB. Supports JPG, JPEG, GIF, PNG, BMP
0 / 10000
More by AudioDIWHY
-
Rotary Encoder Experimenter's Dev Board
UPDATE: new revision 9-29-24 posted. Lower parts count, more reliable software debouncing for the en...
-
Bench 4x2 Bluetooth Mixer
Simple 14HP Eurorack 4x2 synth mixer.outputs are 2x 100mil terminal posts on rear of PCB.You will ne...
-
Anything to Clock--LM311 based
I needed a simple circuit to condition incoming signals so a MCU could read them as clock:--rectify ...
-
Vactrol Based Audio Envelope Follower
An audio envelope follower based on a 5C3 Vactrol. Useful for auto-wah (send its output to a bandpas...
-
Warm Floater Eurorack Power Extender
I ran out of physical connections on my Eurorack Power supply. This PCB supplies 1 input and 3 outpu...
-
"KiCADSR" Euro Envelope Generator
This is my first project using KiCAD for EDA instead of Autodesk Eagle.I wanted to see if I had the ...
-
Low Noise Preamp based on Arp 2600 Synthesizer
The Arp 2600 synthesizer has a preamp that takes an unbalanced signal and amplifies it 10x, 100x, an...
-
Arp 2600 clone--inverter-mixer
The ARP2600 is a legendary, classic semi-modular analog synthesizer. Its voltage processor circuitr...
-
SEEED XAIO RP2040 ADC and Buffer Board
The SEEED XAIO RP2040 is a fantastic little dev board, featuring the RP2040 MCU.I needed a buffered ...
-
Moog T403B Inspired High Pass Filter
Clone of Moog High Pass filter based on EFM design.Please see the blog post here for more informatio...
-
4 input Mono Eurorack Audio Mixer
I need a few small (but not too small!) Eurorack 4 x 1 DC coupled mixers for my rack.Many simple com...
-
RP2040 Clock Multiplier Development Board
I have some RP2040 code to write and didn't want to Breadboard the hardware, so I whipped up a devel...
-
Anything to Clock--Precision Rectifier
For more details please see this blog post:https://audiodiwhy.blogspot.com/2024/04/anything-to-clock...
-
Hardware Encoder Debounce Board
For details about this project please see this blog post: https://audiodiwhy.blogspot.com/2024/01/ro...
-
DSPG1 4 voice synthesizer on a single PCB
The DSPG1 is a $20 IC--along with a handful of external parts this chip gives you a complete a 4 voi...
-
Son of Warm Floater
I ran out of power spigots in my Eurorack, this simple project takes a 16 conductor +/- 12V, GND, 5V...
-
ARP 2600 Audio Switch
The legendary ARP2600 has a pop free/click free clock driven analog switch. Each rising clock switch...
-
DG401 Audio CMOS switch Experimenter's Board
I was curious how the DGx0x series analog switches sounded and didn't want to breadboard a DG401 wit...
You may also like
-
-
-
-
-
3D printed Enclosure Backplate for Riden RD60xx power supplies
159 1 1 -
-
