|
KiCADKicad
|
ESP8266 Remote Relay
This pcb has a WeMOS D1 Mini with ESP8266 to control the on board relay.
Control of the relay can occur wirelessly, and the ESP8266 UART pins are also available on a header to optionally allow an external RS485 or bluetooth module to be used.
The Github project uses ESP-NOW to communicate between this relay control board and another ESP8266 board that uses a current transformer: https://www.pcbway.com/project/shareproject/SCT013_Current_Monitor_for_ESP8266_cc7ccd2e.html
When the current transformer detects a minimum amount of current present, it uses ESP-NOW to trigger the relay momentarily, wirelessly.
It is used to activate a doorbell chime in a secondary location (basement) when the main floor doorbell rings (it can't normally be heard in the basement).
ESP8266 Remote Relay
*PCBWay community is a sharing platform. We are not responsible for any design issues and parameter issues (board thickness, surface finish, etc.) you choose.
- Comments(0)
- Likes(0)
More by Gadget Reboot
-
40 Pin Cable ESP32-C3 based Test Platform
This is a test platform with 40 inputs and 40 outputs, using an ESP32-C3 Super Mini module with five...
-
Serial UPDI Programmer
USB Serial to UPDI programming board for Atmel devices in the Arduino IDEHas a 5v / 3.3v switch to c...
-
Op Amp Buffer with In/Out Guitar Jacks
The pcb has a guitar input and output jack to easily connect to a breadboard for guitar effect circu...
-
16 Channel Audio Loop Switcher
This is a 16 channel audio loop switcher with 16 inputs and 16 outputs.Analog signals within a +/- 5...
-
16 Switches to RS485 Output Commands
Up to 16 switches or 5v/gnd logic inputs can be monitored and when asserted (input = gnd), a sketch ...
-
MCP42100 Digital Pot Breakout PCB
This breakout board for the MCP42100 dual digital pot has headers that are spaced for breadboard com...
-
Power Supply DC Jack/Screw Term/0.1" Header Breakout with PTC
This breakout board allows connecting a power source via 2.1x5.5mm DC jack, 7.62mm screw terminals, ...
-
16x16 Analog Switch
This 16x16 analog crosspoint switch uses two MT8816 8x16 switch ICs cascaded for a larger matrix.The...
-
Line Level Stereo Input to 3 Stereo Output Sharing PCB
This audio sharing board will take a stereo line input from a 3.5mm jack, buffer it and send it out ...
-
MIDI Breakout In/Out/Thru
This MIDI breakout board has 5 pin DIN jacks and Type A configured 3.5mm TRS jacks for Midi In, Midi...
-
Tandy CoCo Joystick Adapter - Use Digital Inputs for Analog X,Y axis
Use 5v/GND digital signals to control the analog joystick input of a Tandy Color Computer.When input...
-
555 Dual Sound Generator Digital Pot Controlled
An ATTiny1604 can be programmed to control two 555 oscillators to generate melodies or sound effects...
-
LS30 Rotary Joystick to USB Keyboard Adapter
Plug in the 13 pin cable from 1 or 2 LS30 style arcade Rotary Joysticks and this board will send out...
-
Capacitor Bank Switch Box
Capacitor Breakout BoardUse dip switches to put capacitors in parallel in 1nF increments from 1 nF t...
-
Op Amp Twin T Percussion PCB
This is an op amp percussion sound generator based on the Forrest Mims circuit in books such as Gett...
-
1/4 Inch TRS Phone Jack Breakout PCB
This 1/4 inch phone jack TRS breakout board has a 6 pin header forTip, Ring, Sleeve, Switched Tip, R...
-
NPN Transistor Breakout Board
This board can be assembled with machine pin sockets to allow swapping NPN transistors as well as co...
-
GPIO Addressable LED Indicators
This pcb can read 8 digital inputs and display their high/low state on one of 8 addressable LEDs as ...
-
-
-
DIY Transistor Tester | Build Your Own LCR Meter at Home with Arduino Nano
128 0 0 -
-
ESP32-S3 breakout board for motorizing Iron Man helmets
173 0 2 -
-
-
