LM358 Project
The LM358 is a low-power dual operational amplifier integrated circuit, originally introduced by National Semiconductor.[1]
It supports an operating voltage of +3 to +32 volts (single power supply) or ±1.5 to ±16 volts (dual power supplies).
Input voltage can range from −0.3 to +32 volts with single power supply. Small negative input voltages below ground are acceptable because the bipolar junction transistors at the input stage are configured such that their base-emitter junction voltage provides just enough voltage differential between the collector and base for the transistors to function.
LM358 Project
*PCBWay community is a sharing platform. We are not responsible for any design issues and parameter issues (board thickness, surface finish, etc.) you choose.
- Comments(0)
- Likes(0)
More by new_ engineer
-
AD7746_Project
The AD7746 is a high resolution, two channel, high linearity and high accuracy Capacitance-to-Digita...
-
LM317_IC_Project
The LM317 is a popular adjustable positive linear voltage regulator. It was designed by Bob Dobkin i...
-
amplifier_circuit
An amplifier is an electronic device or circuit which is used to increase the magnitude of the signa...
-
LM386 Project
The LM386 is an integrated circuit containing a low-voltage audio power amplifier.[1] It is suitable...
-
2N3904 Project
The 2N3904 is a common NPN bipolar junction transistor used for general-purpose low-power amplifying...
-
LMC6482 Project
The LMC6482 device provides a common-mode range that extends to both supply rails. This rail-to-rail...
-
LM358 Project
The LM358 is a low-power dual operational amplifier integrated circuit, originally introduced by Nat...
-
LM555 Project
The 555 timer IC is an integrated circuit (chip) used in a variety of timer, delay, pulse generation...
-
voltaj and current adjustable power supply
The LM317 is a popular adjustable positive linear voltage regulator. It was designed by Bob Dobkin i...
-
ULN2003_Project
The ULN2003A is an integrated circuit produced by Texas Instruments. It consist of an array of seven...
-
BT139 Project
The BT139 is a four-quadrant TRIAC from NXP that can handle medium power switching of loads up to 60...
-
Arduino_LCD_Project
The Arduino Nano is a small, complete, and breadboard-friendly board based on the ATmega328 (Arduino...
-
NE555P Project
The 555 timer IC is an integrated circuit (chip) used in a variety of timer, delay, pulse generation...
-
LD108633 Project
LD1086DT33TRThe Voltage Regulator is in TO252-3 sheath and has 1.5A output current and 3.3V voltage ...
-
L7805 Regulator Board
The L7805CV is a TO-220 three-pin linear regulator based on the commonly found 7805 that has a maxim...
-
Arduino Shield Board
Arduino shields are the boards, which are plugged over the Arduino board to expand its functionaliti...
-
TPS5430 Module
The TPS5430-Q1 is a high output current PWM converter that integrates a low-resistance high side N-c...
-
MPU6050 Sensor Module
MPU6050 is a Micro Electro-mechanical system (MEMS), it consists of three-axis accelerometer and thr...
-
-
-
3D printed Enclosure Backplate for Riden RD60xx power supplies
80 1 1 -
-
-
-
Sega Master System RGB Encoder Switcher Z80 QSB v1.2
71 0 0 -
18650 2S2P Battery Charger, Protection and 5V Output Board
107 0 0 -
High Precision Thermal Imager + Infrared Thermometer | OpenTemp
523 0 7 -
Sony PlayStation Multi Output Frequency Oscillator (MOFO) v1
147 0 2 -
