|
EagleAutodesk
|
Opamp Designs Demo Board
This board has many opamp circuits. It is a learning tool that will be covered in a YouTube series by ImsaiGuy
Introduction:
Circuit Design:
Part Value Device Package Description PROD_ID
C1 0.1uf CAPACITOR, American symbol
C2 CAPACITOR, American symbol (optional)
C3 0.1uf CAPACITOR, American symbol
C4 0.1uf CAPACITOR, American symbol
C5 0.1uf CAPACITOR, American symbol
C6 CAPACITOR, American symbol (optional)
C7 0.1uf CAPACITOR, American symbol
C8 0.1uf CAPACITOR, American symbol
C9 0.1uf CAPACITOR, American symbol
D1 1n914 DIODE 1N4148
D2 1n914 DIODE 1N4148
IC1 NE555N TIMER
IC2 LM358 Jellybean op-amp
IC3 LM358 Jellybean op-amp
IC4 LM358 Jellybean op-amp
IC5 LM358 Jellybean op-amp
R1 1k RESISTOR
R2 10k RESISTOR
R3 10k RESISTOR
R4 1k RESISTOR
R5 10k RESISTOR
R6 10k RESISTOR
R7 10k RESISTOR
R8 10k RESISTOR
R9 1k RESISTOR
R10 100k RESISTOR
R11 1k RESISTOR
R12 100k RESISTOR
R13 100k RESISTOR
T1 2N2222 or 2N3904 NPN TRANSISTOR
Opamp Designs Demo Board
*PCBWay community is a sharing platform. We are not responsible for any design issues and parameter issues (board thickness, surface finish, etc.) you choose.
- Comments(1)
- Likes(8)
- 1 USER VOTES
- YOUR VOTE 0.00 0.00
-
10design
-
10usability
-
10creativity
-
10content
More by IMSAIGUY
-
Op-amp Test Board
This is a two section board. two dual op-amps can be compared. Half of the device is used in a non-i...
-
Photodiode Amplifier with Gain Settings
just a fun project, 4 gain settings transimpedance amp
-
Tiny RS232 Monitor
YouTube videos describe the circuit. The Rev B board fixes the ground problem and correctly connects...
-
Kaypro ROM Selector Board
Here is my video on the project
-
SDK85 8755 EPROM Adapter
A youtube will follow to explainThis is pin compatible with an 8755 chip which is ROM and I/O. This ...
-
7414 Fast Edges
I've done a couple videos on this subject
-
EL2018 EL2252 board for HP 3458A
Here is how it was done by Agilent. Note: the +V is different between the two EL2018. one uses +15 a...
-
Small Gear Motor Housing
This is a 3D print file for a housing/mount for small gear motors. the motor slides into the housing...
-
Panaplex Display Board
this project is documented on YouTube
-
ATTINY ETC board for ETW-3800 Microprocessor Trainer
this board fits the Heathkit ETW-3800 trainer. it has I2C breakout chips to allow lots of IO to conn...
-
Narrow SO-20 to DIP Adapter
this results in a 0.300" DIP for protoboardsit also includes a spot for a bypass capacitor to be use...
-
Narrow SO-16 to DIP Adapter
the DIP has a 0.300" size for protoboard maximization
-
Tiny IMSAI 8080 Computer
This uses an ATTINY814 microcontroller and a bunch of 74595 shift registers to flash the LEDs and re...
-
Narrow SO-14 SMD to DIP Adapter
I made this for using Attiny414 814 type devices on a protoboard with only 0.3" of width
-
Digital Capacitor Bandpass Filter
uses PE64012 serial programmable digital capacitorhttps://youtu.be/zgKv5fhoEHI
-
Mini-Circuits MAR MMIC Amplifier
When ordering board, choose 0.8mm thickness. This is correct thickness for 50ohm transmission line.R...
-
Weinschel Programmable Attenuator
YouTube video series describes project
-
Electrical Symbol Drafting Stencil
I wanted a drafting template for use with a Micron 08 pen. I had this made with 2.5mm thick clear ac...
-
-
-
-
Tester for Touch Screen Digitizer without using microcontroller
329 2 2 -
Audio reactive glow LED wristband/bracelet with NFC / RFID-Tags
310 0 1 -
-
-
