Description
Mini-Circuits MAR MMIC Amplifier
YouTube video to follow.
When ordering board, choose 0.8mm thickness. This is correct thickness for 50ohm transmission line.
Resistor and Inductor are chosen per the Mini-Circuits datasheet for the part and voltages you are using.
Schematic and Layout
KiCAD schematic
MMIC.kicad_sch
KiCAD Layout
MMIC.kicad_pcb
Dec 06,2024
71 views
Mini-Circuits MAR MMIC Amplifier
1GHz amplifier using MAR-1 type devices
71
0
0
Published: Dec 06,2024
Download Gerber file 2
PCBWay Donate 10% cost To Author
*PCBWay community is a sharing platform. We are not responsible for any design issues and parameter issues (board thickness, surface finish, etc.) you choose.
Under the
Attribution-ShareAlike (CC BY-SA)
License.
Topic
- Comments(0)
- Likes(0)
Upload photo
You can only upload 5 files in total. Each file cannot exceed 2MB. Supports JPG, JPEG, GIF, PNG, BMP
0 / 10000
More by IMSAIGUY
-
Op-amp Test Board
This is a two section board. two dual op-amps can be compared. Half of the device is used in a non-i...
-
Mini-Circuits MAR MMIC Amplifier
YouTube video to follow.When ordering board, choose 0.8mm thickness. This is correct thickness for 5...
-
Weinschel Programmable Attenuator
YouTube video series describes project
-
Electrical Symbol Drafting Stencil
I wanted a drafting template for use with a Micron 08 pen. I had this made with 2.5mm thick clear ac...
-
MiniCircuits GVA-63+ 6GHz Amplifier
This amp is part of a YouTube series from start to finish, It is 10 parts. Here are parts 1 and 10
-
SMD to SIP adapter boards
Note: these are REV B boards that fix any problems shown in the YouTube video.Note: when you order t...
-
Chua's Circuit
YouTube video will followhttps://en.wikipedia.org/wiki/Chua%27s_circuitAnalyzing the circuit using K...
-
MGA-82563 6GHz Amplifier
YouTube video will followDesigned for 50ohm impedance, 0.8mm thickness board requiredBoard tested to...
-
SiTime Clock Oscillators
I made these boards 0.8mm thick. Do not load R5 and R6.
-
LM399 10.000V Voltage Standard
Here are the youtube videos
-
Lorenz Attractor
From Paul Horowitz, the Lorenz attractor for oscilloscope XY display. YouTube video will follow late...
-
Zener Diode Tester
Jumper settings for 5, 10, 15, and 20mA currents
-
Dual and Quad OpAmp SImple Tester
here is a video explaining the board
-
NE5532 Headphone Amplifier
Popular op-amps are NE5532 JRC5532 NJM5532 you might consider JRC4556 for higher currents
-
Linear Optocoupler
note: pin one of the IC's are square pads, load correctly as they point different directions.
-
I2C 6 Digit Nixie Tube Display
Here is YouTube video, note this is part 5 of a series. You might want to watch all five.
-
Gyrator Board
circuits from: https://sound-au.com/articles/gyrator-filters.htm
-
Transistor Training PC Board
youtube video will follow soonPlease don't ask for a BOM or schematic. The board IS the schematic. I...
You may also like
-
-
kmMiniSchield MIDI I/O - IN/OUT/THROUGH MIDI extension for kmMidiMini
74 0 0 -
-
-
Box & Bolt, 3D Printed Cardboard Crafting Tools
120 0 2 -
A DIY Soldering Station Perfect for Learning (Floppy Soldering Station 3.0)
416 0 1 -
Custom Mechanic Keyboard - STM32
243 0 3
