Description
Temperatur Humidity Sensor SHT21
General
Powered by 2 AA Batteries Size 20 x 45 (mm)
Almost SMD 0805
Atmel328p TQFP32
NRF24I01 smd
ATSHA204A chip
FLASH for OTA FTDI, ISP SHT21 Sensor
Description
The Sensor works directly on two AA Batteries or Ni-MH
Settings
Use Sensebender Micro bootloader Set Fuses before upload bootloader FUSES:
L: 0XDE // H: 0XD2 // E: 0X07 (disabled BOD/8Mhz external clock) Set Fuses again, arduino IDE will override it with the default sensebender fuses or modify the board settings in Arduino IDE
Code
https://drive.google.com/drive/folders/1n6fTofcV0yYmATYY_WrYvG40SykEPAi4?usp=sharing
Schematic and Layout
https://drive.google.com/file/d/1KPqzimACOGqzu4tEn0u0h7oqZ1AL9VDo/view?usp=sharing
Jul 23,2020
1,745 views
Temperatur Humidity Sensor SHT21
The Sensor works directly on two AA Batteries or Ni-MH
1745
3
0
10.00 (1)
Published: Jul 23,2020
BOM(Bill of materials)
PCBWay Donate 10% cost To Author
Only PCB
PCB+Assembly
*PCBWay community is a sharing platform. We are not responsible for any design issues and parameter issues (board thickness, surface finish, etc.) you choose.
Under the
Attribution-ShareAlike (CC BY-SA)
License.
- Comments(0)
- Likes(3)
Upload photo
You can only upload 5 files in total. Each file cannot exceed 2MB. Supports JPG, JPEG, GIF, PNG, BMP
0 / 10000
VOTING
1 votes
- 1 USER VOTES
10.00
- YOUR VOTE 0.00 0.00
-
10design
-
10usability
-
10creativity
-
10content
10.00
More by Oleg Oleg
-
Development Board STM32F103RET6
Development Board Series STM32F103RET6Resources on the board3.3/5.0/12V power input/output pinReset ...
-
DAPLINK and STM32 minimum system combination
DAPLINK and STM32 minimum system combination, one data cable can complete the download and debugging...
-
USB to RS232
This is a program verification board. The main verification content is the function of USB to RS232 ...
-
ESP Air Burner
The ESP downloader with Air Burnner interface uses probes instead of DuPont cables.
-
Docking station USB3.1
Using GL3520 USB 3.1 HUB chip,Supports super high speed, high speed and full speed USB connection, f...
-
RX5808 open source receiver
5.8g open source receiver, can receive 5.8g signal, AV video signal output. Rx5808 dual-reception fu...
-
5.8G image transmission module
It can be used for AV signal audio and video wireless transmission; baby monitor; wireless camera se...
-
GRBL-ESP32
esp32s 3d is suitable for GRBL and marlin software
-
STM32 Sensor Node
A Small STM32F103C8T6 board with all functional pins exposed. Similar to the BluePill Board except:N...
-
2.8 inch TFT touch screen
The module uses a 2.8-inch TFT color LCD screen. The module is compatible with punctual atomic 2.8TF...
-
LED dot matrix clock
LED dot matrix electronic clock based on 51 single chip microcomputer.Based on STC15W4K series ultra...
-
STM32F411Cx 401Cx minimum system + J-LINK debugger
The STM32F411 / 401 microcontroller belongs to the STM32 Dynamic Efficiency series. These devices ar...
-
Small passive DC constant current electronic load
IntroductionA small passive DC adjustable constant current (CC) electronic load with temperature-con...
-
Small jlinkV9 downloader V1.0
Adopt typec interface, stm32f205 master control, lead SWD, SWO, support virtual serial port, resista...
-
IP2325 dual string lithium battery charging module
Miniature charger for dual lithium batteries.Since the IP2325 does not have a charge balancing funct...
-
Electronic switch
The operating voltage is within 30V. Depends on the PMOS voltage.
-
Power supply module NAE20S08
Is based on SY8288A / JW5068A series power supply ic Volume: 10x10x6mm Input range: 4-23vin Output: ...
-
Solder paste dispenser
A portable miniature intelligent electric SMT solder paste dispensing pen supports quantitative extr...
You may also like
-
-
-
-
kmMiniSchield MIDI I/O - IN/OUT/THROUGH MIDI extension for kmMidiMini
137 0 0 -
DIY Laser Power Meter with Arduino
212 0 2 -
-
Box & Bolt, 3D Printed Cardboard Crafting Tools
186 0 2
