NVPI5-2242T RPI HAT
NVMe (M.2 M-Key 2230, 2242 PCIe Gen3 x1) SSD HAT for Raspberry Pi 5
NVMe HAT PCB with M.2 Slot (M-Key)
Features:
- Compatible with other HAT shield
- Support boot from the NVMe drive
- 30mm length Flat Flex Cable
- Supports installation of official active coolers
- Dual LED Indicators: “PWR” and “ACT”
- Supports 2230/2242 NVME M2 SSD only
- 40-Pin Raspberry Pi HAT Connector Support
- M.2 Standard-Compliant Power System
Packing List:
- 1 x NVPI5-2242T
- 2 x PCIe FFC cable (30mm length)
- 2 x PCIe FFC cable (60mm length)
- 4 x M2.5x14mm F/F Spacers
- 4 x M2.5x6+6mm F/M Spacers
- 5 x M2.5x5mm Screws
- 2 x M2x4mm Screws
- 1x 40-pin male-female HAT connector
Getting started
Firmware
Make sure your Raspberry Pi 5 firmware is up to date with the 2023-12-06 or later version. Software update on the RPi OS should do this for you, but you can force it by running sudo rpi-eeprom-update in the Terminal.
If you have updated your firmware and want to boot from the NVMe drive, you might have to get technical and run sudo rpi-eeprom-config --edit from the Terminal and change the BOOT_ORDER to be 0x416 instead of 0x41.
To enable experimental and not-officially-supported PCIe 3 mode, add the follow line to the [all] section at the end of your Raspberry Pi /boot/config.txt file like this:
# Enable the PCIe external connector
dtparam=pciex1
# Force Gen 3.0 speeds
dtparam=pciex1_gen=3
Booting from NVMe
If you want to boot from the NVMe drive follow these extra steps:
- Format the drive using Raspberry Pi Imager
- Shutdown
- Remove your microSD card
- Power back on
Notes
- Always power off your RPi and disconnect the power supply before installing or uninstalling the NVPI5-2242T and NVPI5-2280B;
- NVPI5-2242T and NVPI5-2280B offers a general purpose PCIe x1 connection;
- We do not recommend WD Green SSDs at this time. Drives such as the SN350 are temperamental with the CM4 and RPi 5.
Documentations
- Comments(0)
You might like
-
-
Power Over Ethernet HAT (F) For Raspberry Pi 5, High Power, Onboard Cooling Fan, With Metal Heatsink, Supports 802.3af/at network standard$19.00 or 1900 BeansRedeem Now
-
PCIe To M.2 Adapter for Raspberry Pi 5, Supports NVMe Protocol M.2 Solid State Drive, High-speed Reading/Writing, HAT + Standard$7.00 or 700 BeansRedeem Now
-
-
-
-
-
RP2040-Tiny Development Board, Based On Official RP2040 Dual Core Processor, USB Port Adapter Board Optional$5.00 or 500 BeansRedeem Now
-
-8%RP2040-Tiny Development Board, Based On Official RP2040 Dual Core Processor, USB Port Adapter Board Optional$4.00 or 400 BeansRedeem Now
-
RP2040-GEEK Development Board, Based On RP2040 Microcontroller, With 1.14inch 65K Color LCD$9.89 or 989 BeansRedeem Now
-
Nano Base Board (A) for Raspberry Pi Compute Module 4, Same Size as the CM4$13.00 or 1300 BeansRedeem Now
-
-
-
HRB8825 Stepper Motor HAT For Raspberry Pi, Drives Two Stepper Motors, Up To 1/32 Microstepping$17.00 or 1700 BeansRedeem Now