|
KiCADKicad
|
DC-DC Converter for Car
DC-DC converter for car [12V / 13.8V....24V, 2A max, adjustable]
In the car, to power a laptop, a medium power audio amplifier that is powered at more than 12V or whose device requires a supply voltage
between 13.8V and 24V it is recommended to use a DC-DC converter that connects to lighter socket.
The maximum limited current is 2A between 13.8V and 16V and decreases approximately with a linear slope (from 0.1A / 2V) to 1.2A at 24V. The recommended limits for continuous operation are consider half. At the base of the circuit is MC34063. The output voltage is adjusted from RV1. The converter is protected at the input and output with diodes. For 60uH coil, if you don't have,
a standard inductor can be purchased, but rewinding is required (for 1mm wire we have 32 turns). The MPT3055E MOSFET transistor can be replaced with IRF530 / IRF630 / IRF740 / IRF840. MBR735 diodes can be replaced with BYW29. All capacitors should be Low ESR.
Have fun with it !
DC-DC Converter for Car
*PCBWay community is a sharing platform. We are not responsible for any design issues and parameter issues (board thickness, surface finish, etc.) you choose.
- Comments(0)
- Likes(0)
- 0 USER VOTES
- YOUR VOTE 0.00 0.00
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
More by Cristian Pitigoi
- LEDs Stars Hello everyone! I'm signing up for this competition with a small project designed to attract your a...
- Audio amplifier with LM386 (and BASS boost) Audio amplifier with LM386 (and BASS boost)Hello everyone!Circuit descriptionThe LM386 is quite a ve...
- Audio amplifier 25W TDA2030 Audio amplifier 25W TDA2030A fairly well-known and interesting montagePresentationThe presented audi...
- Raspberry Pi Pico Expansion Board Hello everyone!This is my new PCB design. I wanted to share it with you on this platform.This is an ...
- Adjustable voltage power supply Among the most important electronic devices in the electronics laboratory is the voltage source. Thi...
- Digital Clock with AT89C2051 Circuit OperationShort SW2 presses cycle through displaying the current time in HH:MM and MM:SS form...
- Switch based light sensor Hi!The circuit shown can be used to turn on the light in the garden, or some light panels / advertis...
- LM3909 flashing indicator I present to you a circuit which is a little outdated, but quite pleasant for some, I saw that this ...
- The use of IoT technology for monitoring specific electrical parameters of autonomous power systems Hello everyone!A brief introduction of this project.What you see presented here is a home made (or D...
- ESP32 Expansion Board Expansion board for ESP32Hello everyone!This is my new PCB design. I wanted to share it with you on ...
- 4 Digits 7 Segments CC Display Module with 74HC595 Hello! This time I want to present an 7-segment four digit display controlled by two 74HC595.The LED...
- Adjustable voltage power supply Adjustable voltage power supplyAmong the most important electronic devices in the electronics labora...
- ARDUINO LCD 1602 SHIELD + KEYBOARD ARDUINO LCD 1602 SHIELD + KEYBOARDThe LCD1602 shield can be mounted together with an Arduino Nano de...
- Double voltage source Circuit presentationDouble voltage source + 15V / -15V and + 5V / -5V stabilizedThis circuit offers ...
- Monitor for 12V batteries Monitor for equal voltage at the terminals of two 12V batteries.Circuit presentation Most 24V back-u...
- Variable stabilizer for low voltages Variable stabilizer for low voltagesThe presented circuit allows to obtain stabilized voltages betwe...
- Simple Temperature Regulator Simple temperature regulatorCircuit descriptionThe temperature controller uses as a temperature tran...
- Audio balance indicator Technical data: - supply voltage 12-15V; - minimum level of the audible signal applied at the input&...
-
-
-
-
-
-
3D printed Enclosure Backplate for Riden RD60xx power supplies
154 1 1 -
-