|
|
NPN Transistor BC547 |
x 2 | |
|
|
3mm LED |
x 3 | |
|
|
C 100uF/16V |
x 2 | |
|
|
R 100 ohm 1/4W or 1/6W |
x 2 | |
|
|
R 10K ohm 1/4W or 1/6W |
x 2 | |
|
|
Switch SPDT SS12D00G3 |
x 1 | |
|
|
CR2032 Coin Battery |
x 1 | |
|
|
CR2032 Coin Battery Holder |
x 1 | |
|
|
Pin Back |
x 1 |
LED blink_ing RoBadge#2 - Basic Soldering Kit
You can support/donate by download gerber here
This article is proudly sponsored by PCBWAY.
PCBWAY make high quality prototyping PCBs for people all over the world. Try it for your self and get 10 PCBs for just $5 at PCBWAY with very great quality, Thanks PCBWAY. The Robadge#2 that I developed for use in this project uses PCBWAY PCB services. In this instructables, I will show you how to build Robadge#2 LED Blinking Robot Badge. Let's get started!
Part List:
2x NPN Transistor BC527
3x LED 3mm
2x C 100uF/16V
2x R 100 ohm 1/4W or 1/6W
2x R 10K ohm 1/4W or 1/6W
1x Switch SPDT SS12D00G3
1x CR2032 Coin Battery
1x CR2032 Coin Battery Holder
1x Pin Back
Schematics:
The leg hole for the resistor on the PCB is designed for a size 1/6w resistor, but you can also use a size 1/4w resistor by bending the leg on one side then insert to PCB board as shown in the picture.
You can insert other components such as Transistors, Capacitors and Switch following the sign on the PCB board.
Insert the LEDs, ensuring the short legs are towards the centre of the board.
Turn the board over and solder all legs components.?
Using your cutters it’s time to snip the legs from the components. You should wear eye protection as the legs can fly off!
Place the battery holder into the provided holes from back of PCB.
Turn the board over again then solder the legs in place.
Using your pliers hold the pin back onto the centre of the pad. Tin your soldering iron then hold the tip down with the pliers heat the pin back and hold the iron in place until you notice the solder flow to the edge.
Insert the battery writing side facing out.
Write the name you want, using permanent marker on the white area below the PCB.
Slide the switch lever to the right ON position.
Hopefully you enjoy your Robadge#1. If you do, please share your makes, share the link, like and subscribe Instructables & Youtube. As always, if you have any questions please let me know!
https://www.pcbway.com/?from=bluino
https://www.pcbway.com/project/shareproject/LED_Blinking_RoBadge_2___Basic_Soldering_Kit.html
LED blink_ing RoBadge#2 - Basic Soldering Kit
*PCBWay community is a sharing platform. We are not responsible for any design issues and parameter issues (board thickness, surface finish, etc.) you choose.
- Comments(0)
- Likes(7)
More by Bluino Bluino
-
ESP32-Cam Motor Driver Shield L293D
Android App: ESP32 Camera Wifi Robot CarTutorial Assembly:https://www.instructables.com/DIY-ESP32-Ca...
-
LED Blinking Robot Badge - Soldering Kit
This article is proudly sponsored by PCBWAY.PCBWAY make high quality prototyping PCBs for people all...
-
3 Panel LED Dot Matrix MAX7219 for Common Anode Dot Matrix
Part List per Panel:1 x PCB LED Dot Matrix MAX7219 (PCBWay)1 x Led Dot Matrix 8x8 Common Anode1 x IC...
-
2 Panel LED Dot Matrix MAX7219 for Common Anode Dot Matrix
Part List per Panel:1 x PCB LED Dot Matrix MAX7219 (PCBWay)1 x Led Dot Matrix 8x8 Common Anode1 x IC...
-
IoT Basic Kit ESP8266 Wemos D1 Mini
Part List:1 x PCB IoT Basic Kit (PCBWay)1 x ESP8266 Wemos D1 Mini board1 x OLED I2C 128x641 x Humidi...
-
ESP32 IoT Basic Shield
Part List:1 x PCB ESP32 Basic Shield (PCBWay)1 x ESP32 DEV KIT V1 board1 x LED 5mm1 x LED 3mm1 x Act...
-
Nodemcu Amica ESP8266 IoT Starter Shield
Learn Basic IoT use ESP8266 boards is very easy with Nodemcu IoT Starter Shield board and following ...
-
ESP32 Motor Shield 2WD
Control Robot Car 4WD Mecanum Wheel use app Android, install app here:https://play.google.com/store/...
-
ESP32 Motor Shield 4WD Mecanum Wheel
Control Robot Car 4WD Mecanum Wheel use app Android, install app here:https://play.google.com/store/...
-
ESP32 IoT Starter Shield Ver 2.0
The difference from the previous version is that there is an additional slot for the HCSR04 ultrason...
-
nanBluino - DIY Arduino Nano USB Type-C
Overview"Arduino is an open-source electronics prototyping platform based on flexible, easy-to-use h...
-
Drawbot Wifi ESP32 GRBL - Drawing Robot Plotter Pen
OverviewThe Drawbot is a drawing art robot that can draw. You will needs two stepper motors, a micro...
-
Topeduino - DIY Arduino Uno USB Type-C use Solder Paste Stencil
Overview"Arduino is an open-source electronics prototyping platform based on flexible, easy-to-use h...
-
Eggbot Wifi ESP32 - Drawing Robot Plotter Pen
OverviewThe Eggbot is a drawing art robot that can draw on spherical or egg-shaped objects. You coul...
-
ESP32 Balancing Robot Shield
Part list:1 x PCB ESP32 Balancing Robot Shield (PCBWay)1 x ESP32 DEVKIT V1 board2 x Stepper Motor Dr...
-
Pi Pico Starter Shield
Easy Way to Started learn Raspberry Pi Pico, based on official tutorial download Get Started Pi Pico...
-
ESP32 IoT Starter Kit
Learn Basic IoT use ESP32 boards is very easy with ESP32 IoT Starter Kit board and following the 110...
-
LED blink_ing RoBadge#2 - Basic Soldering Kit
You can support/donate by download gerber here This article is proudly sponsored by PCBWAY.PCBWAY ma...
-
-
-
kmMiniSchield MIDI I/O - IN/OUT/THROUGH MIDI extension for kmMidiMini
125 0 0 -
DIY Laser Power Meter with Arduino
174 0 2 -
-
Box & Bolt, 3D Printed Cardboard Crafting Tools
164 0 2
