Microcontroller minimum system board-GD32F130G8U6
Microcontroller minimum system board-GD32F130G8U6
Low cost and high performance
Using ARM Cortex-M3 RISC core
72M frequency
64KB of FLASH memory
8KB of SRAM memory
The minimum system board of the single chip microcomputer-GD32F130G8U6,
the core board size is only 4.4cm * 4.4cm, and leads to the remaining IO ports.
With two LED indicators and power indicator, with KEY button,
RST reset button, P2 SWD download debugging interface, P6 OLED interface.
The core board can use the MINI_USB interface to supply power to the core board
Using ARM ○ R Cortex ○ R-M3 RISC core,
72M FLASH memory with 64KB frequency and 8KB SRAM memory,
operating voltage 3.3V, I / O port and peripherals are hung on two APB buses,
a 12-bit ADC , 5 general-purpose 16-bit timers, one 32-bit timer,
one PWM advanced timer, two SPIs, two I2Cs, and two USARTs.
Microcontroller minimum system board-GD32F130G8U6
*PCBWay community is a sharing platform. We are not responsible for any design issues and parameter issues (board thickness, surface finish, etc.) you choose.
- Comments(0)
- Likes(2)
- 1 USER VOTES
- YOUR VOTE 0.00 0.00
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
-
10design
-
10usability
-
10creativity
-
10content
More by Oleg Oleg
- Development Board STM32F103RET6 Development Board Series STM32F103RET6Resources on the board3.3/5.0/12V power input/output pinReset ...
- DAPLINK and STM32 minimum system combination DAPLINK and STM32 minimum system combination, one data cable can complete the download and debugging...
- USB to RS232 This is a program verification board. The main verification content is the function of USB to RS232 ...
- ESP Air Burner The ESP downloader with Air Burnner interface uses probes instead of DuPont cables.
- Docking station USB3.1 Using GL3520 USB 3.1 HUB chip,Supports super high speed, high speed and full speed USB connection, f...
- RX5808 open source receiver 5.8g open source receiver, can receive 5.8g signal, AV video signal output. Rx5808 dual-reception fu...
- 5.8G image transmission module It can be used for AV signal audio and video wireless transmission; baby monitor; wireless camera se...
- GRBL-ESP32 esp32s 3d is suitable for GRBL and marlin software
- STM32 Sensor Node A Small STM32F103C8T6 board with all functional pins exposed. Similar to the BluePill Board except:N...
- 2.8 inch TFT touch screen The module uses a 2.8-inch TFT color LCD screen. The module is compatible with punctual atomic 2.8TF...
- LED dot matrix clock LED dot matrix electronic clock based on 51 single chip microcomputer.Based on STC15W4K series ultra...
- STM32F411Cx 401Cx minimum system + J-LINK debugger The STM32F411 / 401 microcontroller belongs to the STM32 Dynamic Efficiency series. These devices ar...
- Small passive DC constant current electronic load IntroductionA small passive DC adjustable constant current (CC) electronic load with temperature-con...
- Small jlinkV9 downloader V1.0 Adopt typec interface, stm32f205 master control, lead SWD, SWO, support virtual serial port, resista...
- IP2325 dual string lithium battery charging module Miniature charger for dual lithium batteries.Since the IP2325 does not have a charge balancing funct...
- Electronic switch The operating voltage is within 30V. Depends on the PMOS voltage.
- Power supply module NAE20S08 Is based on SY8288A / JW5068A series power supply ic Volume: 10x10x6mm Input range: 4-23vin Output: ...
- Solder paste dispenser A portable miniature intelligent electric SMT solder paste dispensing pen supports quantitative extr...
-
-
-
DIY Transistor Tester | Build Your Own LCR Meter at Home with Arduino Nano
46 0 0 -
-
-
ESP32-S3 breakout board for motorizing Iron Man helmets
128 0 2 -
Build a Walking Robot: Theo Jansen Style 3D Printed Octopod
213 0 5 -
-