|
EagleAutodesk
|
ARP 2600 Audio Switch
The legendary ARP2600 has a pop free/click free clock driven analog switch. Each rising clock switches between Input A to and B to an output C. This 5HP Euro module works the same way--use it to seamlessly switch Audio or control signals using a clock signal's rising edge.
More information in the blog post here:
https://audiodiwhy.blogspot.com/2023/09/arp-2600-voltage-processor-final.html
Information about using the DG401 IC for audio switching is here:
https://audiodiwhy.blogspot.com/2023/07/arp-2600-voltage-processors-part-four_19.html
https://audiodiwhy.blogspot.com/2023/07/arp-2600-voltage-processors-part-four.html
If you want to experiment with DG401's for audio, please look at the community project here:
If you build this project you may want to get the front panel gerber fabricated as well. If so, I suggest fabricating the PCB with a black soldermask and white silks. Check the box to hide the project code (an extra $1.50USD at PCBWAY).
ARP 2600 Audio Switch
*PCBWay community is a sharing platform. We are not responsible for any design issues and parameter issues (board thickness, surface finish, etc.) you choose.
- Comments(0)
- Likes(0)
More by AudioDIWHY
-
JTAG to SWD Converter
Simple JTAG to SWD adapter.My use case is Segger J-LINK EDU MINI to Raspberry Pi Pico but this board...
-
Rotary Encoder Experimenter's Dev Board
UPDATE: new revision 9-29-24 posted. Lower parts count, more reliable software debouncing for the en...
-
Bench 4x2 Bluetooth Mixer
Simple 14HP Eurorack 4x2 synth mixer.outputs are 2x 100mil terminal posts on rear of PCB.You will ne...
-
Anything to Clock--LM311 based
I needed a simple circuit to condition incoming signals so a MCU could read them as clock:--rectify ...
-
Vactrol Based Audio Envelope Follower
An audio envelope follower based on a 5C3 Vactrol. Useful for auto-wah (send its output to a bandpas...
-
Warm Floater Eurorack Power Extender
I ran out of physical connections on my Eurorack Power supply. This PCB supplies 1 input and 3 outpu...
-
"KiCADSR" Euro Envelope Generator
This is my first project using KiCAD for EDA instead of Autodesk Eagle.I wanted to see if I had the ...
-
Low Noise Preamp based on Arp 2600 Synthesizer
The Arp 2600 synthesizer has a preamp that takes an unbalanced signal and amplifies it 10x, 100x, an...
-
Arp 2600 clone--inverter-mixer
The ARP2600 is a legendary, classic semi-modular analog synthesizer. Its voltage processor circuitr...
-
SEEED XAIO RP2040 ADC and Buffer Board
The SEEED XAIO RP2040 is a fantastic little dev board, featuring the RP2040 MCU.I needed a buffered ...
-
Moog T403B Inspired High Pass Filter
Clone of Moog High Pass filter based on EFM design.Please see the blog post here for more informatio...
-
4 input Mono Eurorack Audio Mixer
I need a few small (but not too small!) Eurorack 4 x 1 DC coupled mixers for my rack.Many simple com...
-
RP2040 Clock Multiplier Development Board
I have some RP2040 code to write and didn't want to Breadboard the hardware, so I whipped up a devel...
-
Anything to Clock--Precision Rectifier
For more details please see this blog post:https://audiodiwhy.blogspot.com/2024/04/anything-to-clock...
-
Hardware Encoder Debounce Board
For details about this project please see this blog post: https://audiodiwhy.blogspot.com/2024/01/ro...
-
DSPG1 4 voice synthesizer on a single PCB
The DSPG1 is a $20 IC--along with a handful of external parts this chip gives you a complete a 4 voi...
-
Son of Warm Floater
I ran out of power spigots in my Eurorack, this simple project takes a 16 conductor +/- 12V, GND, 5V...
-
ARP 2600 Audio Switch
The legendary ARP2600 has a pop free/click free clock driven analog switch. Each rising clock switch...
-
-
-
kmMiniSchield MIDI I/O - IN/OUT/THROUGH MIDI extension for kmMidiMini
110 0 0 -
DIY Laser Power Meter with Arduino
162 0 2 -
-
Box & Bolt, 3D Printed Cardboard Crafting Tools
153 0 2 -
A DIY Soldering Station Perfect for Learning (Floppy Soldering Station 3.0)
554 0 2
