|
|
Capacitor 1uf 0805 |
x 5 | |
|
|
DB25 male solder through-hole vertical |
x 1 | |
|
|
1x2 2.54mm pin header horizontal |
x 1 | |
|
|
1x2 2.54mm jumper |
x 1 | |
|
CUS-12TBNIDEC COPAL ELECTRONICS
|
x 1 | |
|
SP3232EBCN-L/TRMaxLinear, Inc.
|
x 1 |
|
KiCADKicad
|
Feather MounT
See: https://github.com/bkw777/PDDuino
See: https://github.com/bkw777/MounT
Use ENIG finish because the zig-zag pin rows are actually a socket without needing a socket. You want them gold plated because they are contacts.
Fits any Adafruit Feather board. The most useful for PDDuino are the ones with a built-in SD card reader:
https://www.adafruit.com/product/2795
https://www.adafruit.com/product/2796
And this lipo battery is an ideal add-on: https://www.adafruit.com/product/1570
Fits any machine with a DB25 Female DTE RS-232 serial port. This is a slightly non-standard combination, usually a 25-pin DTE serial port is male. But machines with this configuration include:
Kyotronic KC-85
TRS-80 / TANDY Model 100, 102, 200, 600
NEC PC-8201, PC-8300, PC-8401 "Starlet", PC-8501
Olivetti M10
Feather MounT
*PCBWay community is a sharing platform. We are not responsible for any design issues and parameter issues (board thickness, surface finish, etc.) you choose.
- Comments(0)
- Likes(2)
More by Brian K. White
-
MiniNDP - RAMDisk for TRS-80 Model 100/102/200
Re-implementation of Node Systems DATAPAC.256k ram disk for TRS-80 Model 100, TANDY Model 102, TANDY...
-
512k MRAM IC-Card for TANDY WP-2
REQUIRES 1.2 mm PCBWarning: The total cost for parts for this is around $100 USDThis is an "IC-Card"...
-
LPT Capture
Capture the output from a parallel printer port.
-
TANDY Portable Disk Drive Cable
This is the special level-shifting RS-232 cable needed for the Tandy Portable Disk Drive aka Brother...
-
Molex 7880x-28 PCB Carrier
Order usingMaterial: NylonProcess: SLS (or MJF if PCBWAY starts offering it)This is the plastic ca...
-
FluxEngine Hat
Adapter PCB and snap cover for FluxEngineProvides both a 34-pin connector for normal 3.5 inch and 5....
-
Batteries for REXCPM
Provides an on-board memory battery for the REXCPMAssembly notes:For battery holders BT1, BT2, BT3 (...
-
M4ROM_TANDY - Writable multi option rom module for TRS-80 Model 100/102/200
ONLY for TRS-80 / TANDY Models 100, 102, 200Provides 4 virtual 32K EPROM from a single 128K flash ch...
-
M4ROM Programming Adapter for M4ROM_TANDY and M4ROM_27256
Programming adapter to program M4ROM_TANDY and M4ROM_27256 .Solid electrical contact with the center...
-
M4ROM 27256 - Writable multi option rom module for EPSON PX-4, PX-8, TANDY 600, any Molex 78805 socket with standard pinout
Provides 4 virtual 32k EPROM from a single 128k flash chip, in a Molex 78802 form factor to fit in a...
-
TANDY 600 RAM - TINY Version
Tiny version of 96K ram module for TANDY 600The larger card below is the original 96K ram card for c...
-
TANDY 600 RAM 96K THT
96K SRAM module for TANDY 600, all through-hole components version. Replaces Tandy Cat. No. 26-3910...
-
Teensy MounT
https://github.com/bkw777/MounT
-
TANDY 600 192K DUAL RAM
192K SRAM for TANDY 600The original option RAM banks for TANDY 600 are 96K, and the machine can acce...
-
TANDY 200 RAM 48K TSOP
48K Dual-bank option ram module for TANDY 200How to do the legs: https://gist.github.com/bkw777/52d8...
-
reQUAD - RAM Expansion for TRS-80 Model 100
Replaces the internal 32k SRAM in a TRS-80 Model 100 with a software-switchable 4 banks of 32k SRAM ...
-
ScopeShuntX
Shunt resistor for measuring current with an oscilloscope.Inspired by github.com/voltlog/ScopeShuntS...
-
de0-nano fpga rgb2vga
https://github.com/bkw777/rgb2vgahttps://sites.google.com/site/tandycocoloco/rgb2vgaConvert 15khz RG...
-
-
-
kmMiniSchield MIDI I/O - IN/OUT/THROUGH MIDI extension for kmMidiMini
125 0 0 -
DIY Laser Power Meter with Arduino
180 0 2 -
-
Box & Bolt, 3D Printed Cardboard Crafting Tools
165 0 2
