Tandy CoCo EPROM Cartridge
This pcb was designed by Mark J. Blair under GPLv3 License
Blog: https://www.nf6x.net/2013/10/cocoeprompak/
It allows the use of EPROMS with the Tandy TRS-80 Color Computer cartridge expansion port.
2732 through 27256 EPROMS can be programmed with CoCo software and then used with the CoCo like normal cartridges.
Refer to the project blog for details on how to use the pcb, including setting jumpers and using the appropriate EPROM footprint on the PCB.
Two footprints overlap each other and only one can be used per pcb.
Since the component count is so small and I expect this pcb to be hand assembled with each person's special requirements, no BOM has been provided here.
Another person designed a 3D printed cartridge shell for this pcb, available on Thingiverse
https://www.thingiverse.com/thing:2536842
Tandy CoCo EPROM Cartridge
*PCBWay community is a sharing platform. We are not responsible for any design issues and parameter issues (board thickness, surface finish, etc.) you choose.
- Comments(0)
- Likes(6)
More by Gadget Reboot
-
40 Pin Cable ESP32-C3 based Test Platform
This is a test platform with 40 inputs and 40 outputs, using an ESP32-C3 Super Mini module with five...
-
Serial UPDI Programmer
USB Serial to UPDI programming board for Atmel devices in the Arduino IDEHas a 5v / 3.3v switch to c...
-
Op Amp Buffer with In/Out Guitar Jacks
The pcb has a guitar input and output jack to easily connect to a breadboard for guitar effect circu...
-
16 Channel Audio Loop Switcher
This is a 16 channel audio loop switcher with 16 inputs and 16 outputs.Analog signals within a +/- 5...
-
16 Switches to RS485 Output Commands
Up to 16 switches or 5v/gnd logic inputs can be monitored and when asserted (input = gnd), a sketch ...
-
MCP42100 Digital Pot Breakout PCB
This breakout board for the MCP42100 dual digital pot has headers that are spaced for breadboard com...
-
Power Supply DC Jack/Screw Term/0.1" Header Breakout with PTC
This breakout board allows connecting a power source via 2.1x5.5mm DC jack, 7.62mm screw terminals, ...
-
16x16 Analog Switch
This 16x16 analog crosspoint switch uses two MT8816 8x16 switch ICs cascaded for a larger matrix.The...
-
Line Level Stereo Input to 3 Stereo Output Sharing PCB
This audio sharing board will take a stereo line input from a 3.5mm jack, buffer it and send it out ...
-
MIDI Breakout In/Out/Thru
This MIDI breakout board has 5 pin DIN jacks and Type A configured 3.5mm TRS jacks for Midi In, Midi...
-
Tandy CoCo Joystick Adapter - Use Digital Inputs for Analog X,Y axis
Use 5v/GND digital signals to control the analog joystick input of a Tandy Color Computer.When input...
-
555 Dual Sound Generator Digital Pot Controlled
An ATTiny1604 can be programmed to control two 555 oscillators to generate melodies or sound effects...
-
LS30 Rotary Joystick to USB Keyboard Adapter
Plug in the 13 pin cable from 1 or 2 LS30 style arcade Rotary Joysticks and this board will send out...
-
Capacitor Bank Switch Box
Capacitor Breakout BoardUse dip switches to put capacitors in parallel in 1nF increments from 1 nF t...
-
Op Amp Twin T Percussion PCB
This is an op amp percussion sound generator based on the Forrest Mims circuit in books such as Gett...
-
1/4 Inch TRS Phone Jack Breakout PCB
This 1/4 inch phone jack TRS breakout board has a 6 pin header forTip, Ring, Sleeve, Switched Tip, R...
-
NPN Transistor Breakout Board
This board can be assembled with machine pin sockets to allow swapping NPN transistors as well as co...
-
GPIO Addressable LED Indicators
This pcb can read 8 digital inputs and display their high/low state on one of 8 addressable LEDs as ...
-
-
-
kmMiniSchield MIDI I/O - IN/OUT/THROUGH MIDI extension for kmMidiMini
113 0 0 -
DIY Laser Power Meter with Arduino
162 0 2 -
-
Box & Bolt, 3D Printed Cardboard Crafting Tools
156 0 2 -
A DIY Soldering Station Perfect for Learning (Floppy Soldering Station 3.0)
559 0 2
