How to Generate Gerber, Drill Files and Centroid File From Eagle 9.6.2

In this tutorial, we will show you how to generate Gerber files and drill files from Autodesk Eagle 9.6.2 CAD version.Generate Gerber, Drill File and Centroid File (PnP File)Open the control panel of ...

Tutorial PCB design Gerber Eagle

Introduction to Current Divider

Hello readers! I hope you are doing well. Welcome to the detailed guide on the introduction to the current divider. Electrical circuits are all about the right current flow from one point to the other...

How to generate Gerber files from CircuitMaker 2.2.1.6?

This guide is about how to export Gerber file from CircuitMaker 2.2.1.6.Step 1: Open the PCB design file first, and then open the "Project" menu and click "Generate outputs", as shown below.Step 2: Af...

CircuitMaker Gerber PCB

How to Export Gerber Files in DesignSpark PCB V11.0.0?

Software Required for This Tutorial: DesignSpark PCB V11.0.0Example: chipKIT Max32.pcbTips: Before exporting Gerber files, ensure that your PCB design undergoes a comprehensive design check. This chec...

Gerber DesignSpark PCB

How to add a Board Outline to Gerber Plots in DesignSpark PCB V11.0.0?

Software Required for This Tutorial: DesignSpark PCB V11.0.0.If the Outline layer is not added before running Gerber, the following situation may occur when you click Run:In this case, what is needed ...

Gerber Board Outline DesignSpark PCB

How to Generate Centroid File from DesignSpark PCB V11.0.0?

Software Required for This Tutorial: DesignSpark PCB V11.0.0This tutorial demonstrates how to export centroid files from DesignSpark PCB Explorer 11.0.Example: chipKIT Max32.pcb.Step1: Open DesignSpar...

Centroid File DesignSpark PCB

How to Generate Gerber Files in Fusion 360?

Once you have completed the PCB design in Fusion 360, the next step is to export production files to prepare for PCB manufacturing. Therefore, this tutorial will guide you on how to export Gerber file...

Gerber Fusion 360 Autodesk

How to Generate a Pick and Place File in .csv Format from Fusion 360?

Fusion 360 is the first and only integrated cloud CAD, CAM, CAE, and PCB software platform of its kind.When you finish designing a PCB in Fusion 360 and need to export coordinate files for the PCB man...

Pick and Place CSV Fusion 360 Autodesk

How to Set Shortcut Key in Cadence Allegro PCB Editor?

Setting shortcut key in Allegro can significantly improve work efficiency and lower body burden. In this article, we will introduce the three methods to set shortcut key:Directly defined in the Allegr...

shortcut key Allegro PCB Editor

How to Create a SMD footprint using the Allegro PCB Editor?

We learned about how to creat the pads of 0603 footprint in How to Create SMD pad in Cadence Allegro. In this tutorial, we will continue to demonstrate the process of creating footprint by taking the ...

Tutorial SMD footprint Cadence 17.2 Allegro PCB Editor

How to Create a Through-hole pad using the Allegro Padstack Editor?

This tutorial takes a 1mm through-hole and a 1.6mm pad as an example.Step 1: Find Padstack Editor and then click.Step 2: Select Thru Pin on Start interface.Step 3: Switch to Drill interface and fill o...

Tutorial Through-hole pad Cadence Allegro Padstack Editor

How to Create a SMD pad using the Allegro Padstack Editor?

This tutorial takes GA0603Y103KXBAC31G from Vishay as an example.Step 1: Open the GA0603Y103KXBAC31G data sheet for the package specifications of this device.From the data sheet above, it is obtained ...

Tutorial SMD pad Cadence 17.2 Allegro Padstack Editor

How to Generate Gerber and Drill Files From Fritzing

Fritzing is a low-barrier-to-entry electronic design automation software for the needs of manufacturers and hobbyists.At PCBWay, we recommend our customers provide Gerber in RS-274X format for manufac...

Tutorial PCB design Gerber Fritzing

How to Export Gerber File From PCB Wizard

Generate GerberSelect the menu bar, click on "Tools" -> "CAD/CAM" -> "Export Gerber", as shown in the following figure.Figure 1. Export Gerber Menu Bar OptionAfter clicking, a new interface will...

Tutorial PCB design Gerber PCB Wizard

How to Generate Gerber and Drill Files in Altium Designer 23.5.1

Gerber FilesSelect the menu bar, click "File"->"Fabrication Outputs"->"Gerber Files", as shown in the figure below.After clicking, the Gerber Setup interface will appear. Refer to the red boxes ...

Tutorial PCB design Gerber Altium Design

How to Generate Gerber and Drill Files in KiCad 7.0

Now you can place order directly by PCBWay Plugin for KiCadAfter completing the PCB design in KiCad, the final step is to generate Gerber and drill files, which will be sent to the PCB manufacturers f...

Tutorial PCB design Gerber Kicad

A Comprehensive Guide for 5V DC Power Supply Design

IntroductionHello all! Welcome on board. Here we are going to focus on designing a 5V power supply. We will design the power supply and carry out and explain how to do various calculations including a...

PCB Design Tutorial PCB layout Circuit Altium Designer Fritzing

We try to automatize electronic design for makers

Dear PCBWay Community,After many years of suffering in PCB design, we tried to do something to help makers design their own PCB prototypes quickly. The resulting software is called EBE (Electronic Bra...

PCB Design Tutorial PCB layout Circuit

How to generate BOM and Pick and Place File in Proteus

In this tutorial, let’s see how to generate BOM (Bill of Materials) and CPL (Component Placement List) in Proteus.This tutorial was written for Proteus 8.13 version and the "dsPIC33_REC " sample proje...

proteus bom pick and place file

How to Design the Component Libraries in Altium Designer [Beginners Tutorial]

In this video, you will learn how to design/create a schematic symbol and a PCB footprint (a component library) in Altium designer and attach a 3D model to the footprint. Basically, you will create an...

Altium Designer

1 2 3 4 5 6 7
Ranking Name Answers
1 PCBWay Team 7
2 Dan Pickerill 4
3 Mnazz N 1
4 Ross Feng 1
Back to top