2.1 Amplifier with STK403-240
In this project i use STK403-240 With 3 channel output to make 2.1 amplifier, it will save cost than using one stereo ic + one mono ic stk.
This amp have 3 menus : Satellite Volume controll , Subwoofer Volume controll, and Subwoofer Frequency Controll with trimpot
This 2.1 STK403-240 amplifier requires 24V-0-24V Transformer 5-10A for the power source.
And don't forget to see how to use the stanby function:
connect Stanby to ground = power amplifier off
connect Stanby to +PRE = power amplifier on
The sound produced is powerfull, please watch the video until it's finished
2.1 Amplifier with STK403-240
*PCBWay community is a sharing platform. We are not responsible for any design issues and parameter issues (board thickness, surface finish, etc.) you choose.
- Comments(0)
- Likes(0)
- 0 USER VOTES
- YOUR VOTE 0.00 0.00
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
More by barita
-
Simple audio limiter This limiter circuit use to avoid clips on a mid-power amp.It controll and decrease the input of amp...
-
TIP 41/42 Mini Amplifier SMD The project uses TIP41/42 as the final amplifier, the circuit is made as simple as possible with SMD...
-
LM3875 Amplifier This module is a mono board, so you can make 2 board for stereo or 6 board for 5.1, very recommend t...
-
GOLD-FI Preamp This circuit use a dual op-amp chip for one channel, it works on parallel mode. So it need two op-am...
-
DIY 5.1 Amplifier TPA3116D2 In this project I make a 5.1 amplifier using the TPA3116D2 chip.This amplifier can produce high powe...
-
Subwoofer amplifier STK4044V This subwoofer amplifier using the STK4044V chip, because this chip very low distortion with THD 0.0...
-
DIY Third Order Lowpass Filter PT2351 This lowpass filter PT2351 run in third order with -18dB /oct slope, it means that the resulting sig...
-
STK426-530 STEREO AMPLIFIER In this project I want to make an amplifier using the STK426-530 chip that which is often used in hi...
-
KIA6210AH STEREO AMPLIFIER In this project I want to make a stereo amplifier using the KIA6210ah chip.This chip is capable of p...
-
Class A amplifier IRF610 Very simple class a amplifier with the basic mosfet amp scheme found from google and I modified it u...
-
DIY LM383T Stereo Amplifiier This chip is very rare on the market. Based on datasheet, this chip capable of producing 7Watt/chann...
-
Stereo TDA1554Q Amplifier This chip is capable of producing 2x22Watt power to drive 4-6 inch speakers.Surprisingly, this TDA15...
-
DIY STEREO RCA TO BALANCE XLR CONVERTER Stereo KONVERTER from Unbalance signal to Balance signal for many purposes of audio.The unbalance in...
-
Stereo TPA3116D2 Amplifier Stereo amp using TPA3116D2 chip in dual pbtl which has a great power output about 2x100 watts Max.Th...
-
STEREO LM4766 AMPLIFIER Stereo amp using the Gainclone LM4766 chip which has a great power output about 2x40 watts.The PCB t...
-
STEREO AMPLIFIER TPA3255 CLASS D Simple powerfull class D amplifier using TPA3255 chip.This amplifier can produces power up to 2x315W...
-
Digital active cross over 2.1 This is a simple 2.1 digital active cross over using PT2353H chip.This active cross over have some m...
-
Stereo TDA7266 Mini Amplifier This TDA7266 Chip Amplifier can produce 14Watt Stereo power (2x7Watt) with a single supply 12V
-
MPL3115A2 Barometric Pressure, Altitude, and Temperature Sensor
36 0 0 -
-
Nintendo 64DD Replacement Shell
142 0 1 -
V2 Commodore AMIGA USB-C Power Sink Delivery High Efficiency Supply Triple Output 5V ±12V OLED display ATARI compatible shark 100W
248 4 1 -
How to measure weight with Load Cell and HX711
368 0 3 -
-
Instrumentation Input, high impedance with 16 bit 1MSPS ADC for SPI
502 0 0