Class A amplifier IRF610
Very simple class a amplifier with the basic mosfet amp scheme found from google and I modified it using a paralleled IRF610 mosfet.
Surprisingly the sound produced is very smooth even though the power produced is only about 2Watt.
Please note Resistor R1-R4 is very hot so it needs to be combined with the main heatsink.
You can modify the resistance of this resistor with an 80watt light bulb that has a resistance of 12 ohms, or you can also use a constant current circuit using a transistor.
You only need a 24VDC adapter for the voltage source of this amplifier, and don't forget to set the bias at 1/2VCC (but for me i set it at 8-9V for best audio quality)
Please check the video on Barlex Respectaizer Youtube Channel.
Class A amplifier IRF610
*PCBWay community is a sharing platform. We are not responsible for any design issues and parameter issues (board thickness, surface finish, etc.) you choose.
- Comments(0)
- Likes(0)
More by barita
-
Simple audio limiter
This limiter circuit use to avoid clips on a mid-power amp.It controll and decrease the input of amp...
-
TIP 41/42 Mini Amplifier SMD
The project uses TIP41/42 as the final amplifier, the circuit is made as simple as possible with SMD...
-
LM3875 Amplifier
This module is a mono board, so you can make 2 board for stereo or 6 board for 5.1, very recommend t...
-
GOLD-FI Preamp
This circuit use a dual op-amp chip for one channel, it works on parallel mode. So it need two op-am...
-
DIY 5.1 Amplifier TPA3116D2
In this project I make a 5.1 amplifier using the TPA3116D2 chip.This amplifier can produce high powe...
-
Subwoofer amplifier STK4044V
This subwoofer amplifier using the STK4044V chip, because this chip very low distortion with THD 0.0...
-
DIY Third Order Lowpass Filter PT2351
This lowpass filter PT2351 run in third order with -18dB /oct slope, it means that the resulting sig...
-
STK426-530 STEREO AMPLIFIER
In this project I want to make an amplifier using the STK426-530 chip that which is often used in hi...
-
KIA6210AH STEREO AMPLIFIER
In this project I want to make a stereo amplifier using the KIA6210ah chip.This chip is capable of p...
-
Class A amplifier IRF610
Very simple class a amplifier with the basic mosfet amp scheme found from google and I modified it u...
-
DIY LM383T Stereo Amplifiier
This chip is very rare on the market. Based on datasheet, this chip capable of producing 7Watt/chann...
-
Stereo TDA1554Q Amplifier
This chip is capable of producing 2x22Watt power to drive 4-6 inch speakers.Surprisingly, this TDA15...
-
DIY STEREO RCA TO BALANCE XLR CONVERTER
Stereo KONVERTER from Unbalance signal to Balance signal for many purposes of audio.The unbalance in...
-
Stereo TPA3116D2 Amplifier
Stereo amp using TPA3116D2 chip in dual pbtl which has a great power output about 2x100 watts Max.Th...
-
STEREO LM4766 AMPLIFIER
Stereo amp using the Gainclone LM4766 chip which has a great power output about 2x40 watts.The PCB t...
-
STEREO AMPLIFIER TPA3255 CLASS D
Simple powerfull class D amplifier using TPA3255 chip.This amplifier can produces power up to 2x315W...
-
Digital active cross over 2.1
This is a simple 2.1 digital active cross over using PT2353H chip.This active cross over have some m...
-
Stereo TDA7266 Mini Amplifier
This TDA7266 Chip Amplifier can produce 14Watt Stereo power (2x7Watt) with a single supply 12V
-
-
-
-
kmMiniSchield MIDI I/O - IN/OUT/THROUGH MIDI extension for kmMidiMini
137 0 0 -
DIY Laser Power Meter with Arduino
212 0 2 -
-
Box & Bolt, 3D Printed Cardboard Crafting Tools
186 0 2
