Manuel Caldeira
PORTUGAL • + Follow
Description
Balanced Line Driver
I have on occasion needed a balanced signal to test power amps and so on. This is the second version of the Balanced Line Driver project, but this time I decided to do it right: I got PCBs made and built the project to last and not produce unwanted glitches. Hope you get some benefit from this.
Jul 20,2020
2,827 views
Balanced Line Driver
2 Layers PCB 50.8 x 93.8 mm FR-4, 1.6 mm, 1, HASL with lead, Green Solder Mask, White silkscreen
Convert RCA signal to a Balanced (XLR) signal for noiseless audio.
2827
1
1
10.00 (1)
Published: Jul 20,2020
Download Gerber file 162
PCBWay Donate 10% cost To Author
*PCBWay community is a sharing platform. We are not responsible for any design issues and parameter issues (board thickness, surface finish, etc.) you choose.
Under the
Attribution-ShareAlike (CC BY-SA)
License.
- Comments(1)
- Likes(1)
Upload photo
You can only upload 5 files in total. Each file cannot exceed 2MB. Supports JPG, JPEG, GIF, PNG, BMP
0 / 10000
VOTING
1 votes
- 1 USER VOTES
10.00
- YOUR VOTE 0.00 0.00
-
10design
-
10usability
-
10creativity
-
10content
10.00
More by Manuel Caldeira
-
SMD version - Bluetooth Module Supply and Booster board for tube radio
The SMD version of my Tube Radio Bluetooth Module boardsThe definitive Bluetooth Module PCB to seaml...
-
Capacitor Discharger
Working with tube gear and high-end audio equipment presents certain challenges, the most significan...
-
Bridge Rectifier with Mosfet Voltage Dropper 2024-09-02
This PCB is the perfect solution to replace the selenium rectifier in vintage tube radios with moder...
-
Digital Switched Attenuator - Control Board
I designed and built a 50Ω digitally controlled stepped attenuator for RF work, offering 3dB steps u...
-
Digital Switched Attenuator - Relay Board
I designed and built a 50Ω digitally controlled stepped attenuator for RF work, offering 3dB steps u...
-
Digital Switched Attenuator - Relay Board
I designed and built a 50Ω digitally controlled stepped attenuator for RF work, offering 3dB steps u...
-
Decade Resistor Box using inexpensive 11-position rotary switches, and 3D printed enclosure.
Decade Resistor Box built with cost-effective 11-position rotary switches, making it an affordable y...
-
Magic Eye Switch for Bluetooth Boards
Magic Eye Switch for Bluetooth BoardsThis is an add-on to allow the Bluetooth Boards that I designed...
-
Tube Radio Bluetooth Module boards
The definitive Bluetooth Module PCB to seamlessly add BT to a tube radio, with no buzzing noise, and...
-
Mini-Whip Antenna switcher with Bias-T
A self-contained antenna switcher with Bias-T for the Mini-Whip, with incorporated switching relay.
-
Capacitor Foil-Side detector
Respecting foil capacitor 'polarity' in the restoration of vintage electronics gear is a much-debate...
-
Inverse RIAA Network
This Inverse RIAA Network lets you use your normal signal generator to test phono inputs of an ampli...
-
Wax removal and alignment tool for tube radios
Wax removal and alignment tool for tube radios
-
Dial lamp to LED conversion boards
I recently converted the dial lamps on a Sony CRF-320 receiver to LED's, and the effect was wonderfu...
-
PCB_dial lamp LED boards_SMD
PCBs to convert dial lamps to LEDs on vintage radios, SMD version.
-
Sony CRF-320 replacement gear set
A set of 3 gears for the Sony crf-320 and crf-330 receivers, which are a common source of problems, ...
-
test lead rack
Cable test rack in resin
-
test lead rack
Cable test rack in PETG
You may also like
-
-
-
-
kmMiniSchield MIDI I/O - IN/OUT/THROUGH MIDI extension for kmMidiMini
137 0 0 -
DIY Laser Power Meter with Arduino
212 0 2 -
-
Box & Bolt, 3D Printed Cardboard Crafting Tools
186 0 2
