Description
Jan 05,2021
1,405 views
end-flag
Kettle Controller
2 Layers PCB 61.7 x 60.8 mm FR-4, 1.6 mm, 1, HASL with lead, Blue Solder Mask, White silkscreen
1405
1
0
Published: Jan 05,2021
Download Gerber file 12
PCBWay Donate 10% cost To Author
*PCBWay community is a sharing platform. We are not responsible for any design issues and parameter issues (board thickness, surface finish, etc.) you choose.
Under the
Attribution-ShareAlike (CC BY-SA)
License.
Raspberry Pi 5 7 Inch Touch Screen IPS 1024x600 HD LCD HDMI-compatible Display for RPI 4B 3B+ OPI 5 AIDA64 PC Secondary Screen（Without Speaker）
BUY NOW
ESP32-S3 4.3inch Capacitive Touch Display Development Board, 800×480, 5-point Touch, 32-bit LX7 Dual-core Processor
BUY NOW
Raspberry Pi 5 7 Inch Touch Screen IPS 1024x600 HD LCD HDMI-compatible Display for RPI 4B 3B+ OPI 5 AIDA64 PC Secondary Screen（Without Speaker）
BUY NOW
Topic
- Comments(0)
- Likes(1)
Log in to post comments.
Upload photo
0 / 10000
More by Love ESPs
-
ATMEGA32U4 (LOANARDO KIND)
Smaller and kind a basic kind of Atmega32u4 boardThe 3pin header is to set power either from USB or ...
-
HT7333 breakout
breakout for HT7333 3.3V LDO regulator,..good to be used wit bare esp12 or esp07 modules running on ...
-
A4988 or DRV8825 stepper motor driver breakout
A4988 or DRV8825 stepper motor driver breakout
-
DS18B20 temperature sensor breakout board
DS18B20 temperature sensor breakout board
-
PWM controller for LED or Motor insulated
Pwm input is 3.3 V..if you want to use 5V change resistor 130 ohm to cca 330 ohm.Circuit is made to ...
-
esp-12(07)
So far its the breakout for ESP-12 module, easy to program,...allowing deep sleet by soldering 2 pad...
-
Kettle Controller
Temperature kettle controller allowing you to set temperature when the kettle goes off,...good for t...
-
ESP8266 E-PAPER BOARD
dont know how to delete the project,...got mistake in the schematic,...dont use till fixed!!!!!!!!!!
-
ATMEGA32U4 (LOANARDO KIND)
Smaller and kind a basic kind of Atmega32u4 boardThe 3pin header is to set power either from USB or ...
-
HT7333 breakout
breakout for HT7333 3.3V LDO regulator,..good to be used wit bare esp12 or esp07 modules running on ...
-
A4988 or DRV8825 stepper motor driver breakout
A4988 or DRV8825 stepper motor driver breakout
-
DS18B20 temperature sensor breakout board
DS18B20 temperature sensor breakout board
-
PWM controller for LED or Motor insulated
Pwm input is 3.3 V..if you want to use 5V change resistor 130 ohm to cca 330 ohm.Circuit is made to ...
-
esp-12(07)
So far its the breakout for ESP-12 module, easy to program,...allowing deep sleet by soldering 2 pad...
-
Kettle Controller
Temperature kettle controller allowing you to set temperature when the kettle goes off,...good for t...
-
ESP8266 E-PAPER BOARD
dont know how to delete the project,...got mistake in the schematic,...dont use till fixed!!!!!!!!!!
-
ATMEGA32U4 (LOANARDO KIND)
Smaller and kind a basic kind of Atmega32u4 boardThe 3pin header is to set power either from USB or ...
-
HT7333 breakout
breakout for HT7333 3.3V LDO regulator,..good to be used wit bare esp12 or esp07 modules running on ...
-
A4988 or DRV8825 stepper motor driver breakout
A4988 or DRV8825 stepper motor driver breakout
-
DS18B20 temperature sensor breakout board
DS18B20 temperature sensor breakout board
You may also like
-
-
-
Modifying a Hotplate to a Reflow Solder Station
548 1 5 -
MPL3115A2 Barometric Pressure, Altitude, and Temperature Sensor
320 0 1 -
-
-
V2 Commodore AMIGA USB-C Power Sink Delivery High Efficiency Supply Triple Output 5V ±12V OLED display ATARI compatible shark 100W
794 4 2 -
How to measure weight with Load Cell and HX711
562 0 3
