Kube Multisensor - Analog/Digital I/O Expander Submodule
This is a "submodule" board for the Kube v2 multi sensor project (https://www.pcbway.com/project/shareproject/NodeMCU_v_1_2_Board.html). It is a cerrier board to add additional I/O to the Kube "stack", using the MCP23017 chip for 16 channels of digital I/O, and/or the ADS1115 breakout board (thin or wide) from Adafruit for 4 channels of 16-bit analog input.
The MCP23017 chip address pins are broken out, so you can optionally stack up to 8 of these boards for 128 total digital I/O.
The ADS1115 chip address pin is also broken out, and you can address/stack up to 4 of these units, for 16 total analog I/O channels.
All I/O is broken out to terminal blocks, for easy connections.
### TECHNICAL DETAILS / COMPONENTS
BOM:
1 x This board
1 x MCP23017 - https://amzn.to/2S01Otl
1 x ADS1115 - https://amzn.to/2XxGVM4
Jumper Headers - https://amzn.to/2Jvkg9t
Male/Female Headers - https://amzn.to/2EgvnSs
8 x 4-pin 2.54mm pitch screw terminal - https://amzn.to/2XvnzHN
1 x 6-pin Female header - https://amzn.to/2S0L7y8
### LEARN / TOPIC / BUILD INSTRUCTIONS
Watch Livestream video below for prototype build instructions.
Kube Multisensor - Analog/Digital I/O Expander Submodule
*PCBWay community is a sharing platform. We are not responsible for any design issues and parameter issues (board thickness, surface finish, etc.) you choose.
- Comments(0)
- Likes(0)
- 0 USER VOTES
- YOUR VOTE 0.00 0.00
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
More by BK
-
Kube ESP32 HiLetGo breakout board Kube LED controller board - this replaces the NodeMCU ESP8266 controller boards, with a drop-in repl...
-
PowerWheels Jeep Bar Light LED carrier board Just fill with 5mm White LEDs (like these - https://amzn.to/3kK4Cu9 - and mount inside the light ass...
-
Kube Multisensor - Analog/Digital I/O Expander Submodule This is a "submodule" board for the Kube v2 multi sensor project (https://www.pcbway.com/project/sha...
-
Kube Multisensor - Power Supply Module This is a "submodule" board for the Kube v2 multi sensor project (https://www.pcbway.com/project/sha...
-
Kube Multisensor - NodeMCU Module Board NodeMCU Breakout Board for DHT, Motion, LED Controller and other sensors (project home at https://ww...
-
Kube Multisensor - OLED & Ambimate MS4 Submodule Board ### DESCRIPTIONThis is a "submodule" board for the Kube v2 multi sensor project (https://www.pcbway....
-
NodeMCU DHT/Sensor/LED Controller Breakout Board-v.1.1 ### DESCRIPTION(NEW) Version 1.2 of this board is now ready and available here: https://www.pcbway.c...
-
Modifying a Hotplate to a Reflow Solder Station
26 0 0 -
MPL3115A2 Barometric Pressure, Altitude, and Temperature Sensor
57 0 1 -
-
Nintendo 64DD Replacement Shell
149 0 1 -
V2 Commodore AMIGA USB-C Power Sink Delivery High Efficiency Supply Triple Output 5V ±12V OLED display ATARI compatible shark 100W
273 4 1 -
How to measure weight with Load Cell and HX711
376 0 3 -
-
Instrumentation Input, high impedance with 16 bit 1MSPS ADC for SPI
510 0 0