Jed Margolin
UNITED STATES OF AMERICA • + Follow
Description
Le DeZapper
Le DeZapper décharge la charge statique que vous obtenez en marchant sur le tapis. Cela empêche la charge statique de zapper votre ordinateur lorsque vous branchez une mémoire Flash USB. Connectez l'une des Bornes de masse de métal à l'arrière de l'ordinateur. La LED montre la force de la charge statique.
Si il ya quelque chose
que vous voulez,
ce que vous devez avoir,
tout ce que vous avez
à faire est de
De Faire Vous-Même
Si vous n'êtes pas déjà un Constructeur (et que vous voulez être un) voir mon tutoriel pour construire des Choses à www.jmargolin.com/making/jm_making.htm
JM
May 13,2019
1,183 views
Le DeZapper
Le DeZapper décharge la charge statique que vous obtenez en marchant sur le tapis.
1183
0
1
3.90 (5)
Published: May 13,2019
PCBWay Donate 10% cost To Author
*PCBWay community is a sharing platform. We are not responsible for any design issues and parameter issues (board thickness, surface finish, etc.) you choose.
Under the
Attribution-ShareAlike (CC BY-SA)
License.
- Comments(1)
- Likes(0)
Upload photo
You can only upload 5 files in total. Each file cannot exceed 2MB. Supports JPG, JPEG, GIF, PNG, BMP
0 / 10000
VOTING
5 votes
- 5 USER VOTES
3.90
- YOUR VOTE 0.00 0.00
-
5design
-
5usability
-
6creativity
-
1content
4.25
-
3design
-
3usability
-
3creativity
-
1content
2.50
-
6design
-
1usability
-
1creativity
-
1content
2.25
-
5design
-
5usability
-
5creativity
-
1content
4.00
-
7design
-
6usability
-
7creativity
-
6content
6.50
More by Jed Margolin
-
MyTX4 To Replace The La Crosse TX4U
My TX4 Wireless Sensor Transmitter replaces the La Crosse TX4U wireless sensor which is no longer ma...
-
Audio Tone Burst Generator
The Audio Tone Burst Generator produces a periodic burst of tone at a User-selected audio frequency ...
-
jm_rpi-pico-v6
The Raspberry Pi Pico module is amazing. It is much faster than the Texas Instruments MSP430G2xxx fa...
-
Woof Meter
The Woof Meter is for testing subwoofer speakers to measure their Thiele-Small (TS) parameters. Thes...
-
Precision Low Frequency Signal Generator
The Precision Low Frequency Signal Generator produces a User-selected signal from 10Hz to 90Hz with ...
-
GPS Clock and Armageddon Alarm
A GPS Module using the U-blox NEO6MV2 is used to receive the GPS timing signals to show the exact ti...
-
PB1 - Prototyping Board with Ground Plane and Power Supplies
This board is for prototyping circuits using wire wrap. It has a good ground plane and power supplie...
-
Flame Switch
This board simulates the electrical characteristic of a flame for troubleshooting residential gas fu...
-
PB2 - Prototyping Board for MSP430G2xxx
This board is for prototyping circuits with the Texas Instruments MSP430G2xxx microcontroller. It ca...
-
GP1 - Board for demonstrating how to use an MSP430G2xxx
This board is for demonstrating how to use the Texas Instruments MSP430G2xxx microcontroller. The bo...
-
VGA Adapter for Atari Hard Drivin’/Race Drivin’ Cockpit
This VGA Adapter for Atari Hard Drivin’/Race Drivin’ Cockpit also provides for delaying horizontal a...
-
Phone Selector/Adapter 2-line to 1-line
This converts an RJ11 line with two phone pairs on it to two single line RJ11 jacks. It provides two...
-
Triangle Wave Generator With Adjustable Symmetry
This is a simple circuit using only one IC, a TL084 quad opamp. The integrator integrates the output...
-
Voltage Controlled Audio Oscillator with LM13700s
This is a voltage controlled audio oscillator using two LM13700s. At 1 KHz ARTA software (http://www...
-
Oscillator - Xtal or RC
This is an oscillator that can be stuffed to be either a crystal oscillator (with a 74HC04) or an RC...
-
Sine Wave Generator Using a Johnson Counter
This is a 1KHz audio oscillator using a Johnson Counter. ARTA software (http://www.artalabs.hr/) rep...
-
VGA Adapter For Tektronix TDS 360 Oscilloscope
The Tektronix TDS 360 is a two-channel digital oscilloscope from the middle 1990s. The sampling rate...
-
Atari BattleZone Engine Sound Generator
Atari’s BattleZone game is considered the first real 3D video game. I did the 3D graphics algorithms...
You may also like
-
-
-
kmMiniSchield MIDI I/O - IN/OUT/THROUGH MIDI extension for kmMidiMini
113 0 0 -
DIY Laser Power Meter with Arduino
163 0 2 -
-
Box & Bolt, 3D Printed Cardboard Crafting Tools
156 0 2 -
A DIY Soldering Station Perfect for Learning (Floppy Soldering Station 3.0)
563 0 2
