![]() |
Autodesk InventorAutodesk
|
SCH10/40 1.25" Merge Collector Tool
This tool can be clamped into a reciprocating saw/band saw to cut pipe for an exhaust merge collector, it enables you to accurately cut multiple tubes and easy repeatability
This is for Schedule 10 - 1.50" Tubing
Dimensions:
Nominal: 1.50"
OD: 1.66"(48.3mm)
Wall : 0.109"(2.77mm)
It has 0.1mm clearnance all the way round the tube, for ease of installation but also not too much to cause the tube to move when cutting, some prints may require sanding slightly for the tube to fit perfectly.
For any other sizes please message or leave a comment
The listing includes:
11.5 Degree Merge Collector Jig
3.5 Degree Adapter(Increases the merge angle to 15 degrees)
3 Cylinder Cut Marker
4 Cylinder Cut Marker
5 Cylinder Cut Marker
6 Cylinder Cut Marker
8 Cylinder Cut Marker
Examples of all the pipes at the various cylinder counts at the two merge angles this jig will allow you to cut
this tool also requires an M8 x 30mm Bolt(Bolt can be longer) and an M8 Nut.
To Use the tool:
Cut a pipe to length and slide into the jig, and seat to the bottom of the hole.
Tighten the bolt so the pipe is held firmly in the jig.
Place in jig in the the clamp on the saw so the pipe is vertical and the bolt facing away from the saw blade
Set the jig so the blade will remove the desired depth from the pipe and tighten the clamp on the saw, then make the first cut.
Select the desired cut marker for the cumber of cylinders you are merging and place onto the jig, then draw a mark on one end, then loosen the bolt and rotate this mark to the other side of the cut marker and tighten down the bolt.
Make the second cut, the pipe can then be de bured and the next pipe installed to be cut without having to remove the jig from the clamp on the saw
The depth of cut on the tube will determin the size of the exit when all of the tube are placed together, cutting more will make for a smaller hole.
SCH10/40 1.25" Merge Collector Tool
*PCBWay community is a sharing platform. We are not responsible for any design issues and parameter issues (board thickness, surface finish, etc.) you choose.

Raspberry Pi 5 7 Inch Touch Screen IPS 1024x600 HD LCD HDMI-compatible Display for RPI 4B 3B+ OPI 5 AIDA64 PC Secondary Screen(Without Speaker)
BUY NOW
ESP32-S3 4.3inch Capacitive Touch Display Development Board, 800×480, 5-point Touch, 32-bit LX7 Dual-core Processor
BUY NOW
Raspberry Pi 5 7 Inch Touch Screen IPS 1024x600 HD LCD HDMI-compatible Display for RPI 4B 3B+ OPI 5 AIDA64 PC Secondary Screen(Without Speaker)
BUY NOW- Comments(0)
- Likes(0)

- 0 USER VOTES
- YOUR VOTE 0.00 0.00
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
More by RK Designs
-
-
-
Modifying a Hotplate to a Reflow Solder Station
654 1 5 -
MPL3115A2 Barometric Pressure, Altitude, and Temperature Sensor
358 0 1 -
-
Nintendo 64DD Replacement Shell
322 0 1 -
V2 Commodore AMIGA USB-C Power Sink Delivery High Efficiency Supply Triple Output 5V ±12V OLED display ATARI compatible shark 100W
856 4 2 -
How to measure weight with Load Cell and HX711
594 0 3