rime / Fancy Rats
POLAND • + Follow
Components
Description
XUM1541 - connect Commodore disk drive to PC
XUM1541 allows you to connect Commodore disk drives (i.e. 1541) to PC and read/write to disks.
This board is a 4th revision of my PCB design. It is compact and DIY friendly (only through hole components are required).
Instructions for Windows
Flashing XUM1541
- Download and unpack avrdude: https://github.com/mariusgreuel/avrdude/releases/
- Download latest firmware from OpenCBM repository for PROMICRO 7406 version: https://github.com/OpenCBM/OpenCBM/tree/master/xum1541 at the time this instruction is written: https://github.com/OpenCBM/OpenCBM/blob/master/xum1541/xum1541-PROMICRO_7406-v08.hex
- Copy firmware file to avrdude directory
- Open device manager. Connect XUM1541 to PC and press RESET button on XUM1541 board. A device in LPT & COM ports section will show up for few seconds. Note down what exact port number it was, i.e. COM5.
- Navigate to avrdude directory in Command Prompt, type in command but don't run it yet: avrdude -p m32u4 -c avr109 -P com5 -U flash:w:xum1541-PROMICRO_7406-v08.hex
- Make sure to replace com5 in above command to the port from step 4. Reset XUM1541 and run the command. XUM1541 will be flashed.
Installing software (Windows 7-10 64bit)
Download the installer from: https://github.com/r1me/TapeXUM/releases/download/1.0/xum-installer-x64.zip
This single button installer will detect XUM1541, install required OpenCBM libraries and CBMXfer software.
Code
https://github.com/OpenCBM/OpenCBM
Schematic and Layout
https://github.com/OpenCBM/OpenCBM
Mar 07,2021
6,303 views
XUM1541 - connect Commodore disk drive to PC
2 Layers PCB 53.5 x 47 mm FR-4, 1.6 mm, 1, HASL with lead, Green Solder Mask, White silkscreen
XUM1541 allows you to connect Commodore disk drives (i.e. 1541) to PC and read/write to disks.
6303
18
0
Published: Mar 07,2021
PCBWay Donate 10% cost To Author
*PCBWay community is a sharing platform. We are not responsible for any design issues and parameter issues (board thickness, surface finish, etc.) you choose.
Under the
Attribution-ShareAlike (CC BY-SA)
License.
- Comments(0)
- Likes(18)
Upload photo
You can only upload 5 files in total. Each file cannot exceed 2MB. Supports JPG, JPEG, GIF, PNG, BMP
0 / 10000
More by rime / Fancy Rats
-
Famiclone/Pegasus 9 pin to 15 pin controller adapter
Famiclone/Pegasus 9 pin to 15 pin controller adapterBOM:DB15 Female (remove metal shield)DB9 Male
-
Simple LPTsnd – Covox Speech Thing for PC LPT
This is a fork of Retroianer.de (matze79) THT design, modified by me (rime/Fancy Rats), adjusted for...
-
MX4SIO for PS2 Low Cost
MX4SIO for PS2. "Low cost", revised to use cheaper components.This version uses the most common micr...
-
DrawBridge - Amiga Floppy Disk Reader/Writer for PC
PCB design I've made for the DrawBridge Plus! project by Robert Smith. Based on DrawBridge Plus! sch...
-
XUM1541 - connect Commodore disk drive to PC
XUM1541 allows you to connect Commodore disk drives (i.e. 1541) to PC and read/write to disks.This b...
-
TapeXUM - Capture and write Commodore tapes via USB device
What's TapeXUM ?TapeXUM is a USB device that can read and write to cassettes of Commodore 16/64/VIC-...
-
Parallel port mod for CBM 1571 disk drive
More about parallel port mod for 1571 disk drives: https://ist.uwaterloo.ca/~schepers/1571port.html
-
Parallel port mod for Commodore 1541-II disk drive
More about parallel port mod for disk drives: https://ist.uwaterloo.ca/~schepers/1541port.htmlOnce i...
-
PS/2 Mouse adapter for Commodore 64 (1351 mouse hardware emulation)
PCB design for [M]ouse project, a PS/2 to 1351 mouse adapter for Commodore 64. Simple design, THT co...
-
4 players adapter for Commodore 64
4 players adapter allows user to connect two more joysticks to Commodore 64. A total of 4 controller...
You may also like
-
-
-
-
-
3D printed Enclosure Backplate for Riden RD60xx power supplies
154 1 1 -
-
