Description
Arduino Nano and ESP32 DEV Display Board
This allows the use of an Arduino Nano or an ESP32 Dev board. just load the one you want. then it supports SPI and I2C displays of various voltages.
Schematic and Layout
schematic pdf
disp board.pdf
Dec 24,2021
2,492 views
Arduino Nano and ESP32 DEV Display Board
use various boards to develop various displays
2492
5
0
7.75 (1)
Published: Dec 24,2021
Download Gerber file 35
BOM(Bill of materials)
Centroid file
PCBWay Donate 10% cost To Author
File Last Updated: 2024/02/29 (GMT+8)
File update record
2024-02-2910:28:50
Centroid file is updated.
2024-02-2910:28:50
Parts List (BOM) is updated.
Only PCB
PCB+Assembly
*PCBWay community is a sharing platform. We are not responsible for any design issues and parameter issues (board thickness, surface finish, etc.) you choose.
Under the
Attribution-ShareAlike (CC BY-SA)
License.
Topic
- Comments(0)
- Likes(5)
Upload photo
You can only upload 5 files in total. Each file cannot exceed 2MB. Supports JPG, JPEG, GIF, PNG, BMP
0 / 10000
VOTING
1 votes
- 1 USER VOTES
7.75
- YOUR VOTE 0.00 0.00
-
7design
-
7usability
-
9creativity
-
8content
7.75
More by IMSAIGUY
-
Op-amp Test Board
This is a two section board. two dual op-amps can be compared. Half of the device is used in a non-i...
-
Weinschel Programmable Attenuator
YouTube video series describes project
-
Electrical Symbol Drafting Stencil
I wanted a drafting template for use with a Micron 08 pen. I had this made with 2.5mm thick clear ac...
-
MiniCircuits GVA-63+ 6GHz Amplifier
This amp is part of a YouTube series from start to finish, It is 10 parts. Here are parts 1 and 10
-
SMD to SIP adapter boards
Note: these are REV B boards that fix any problems shown in the YouTube video.Note: when you order t...
-
Chua's Circuit
YouTube video will followhttps://en.wikipedia.org/wiki/Chua%27s_circuitAnalyzing the circuit using K...
-
MGA-82563 6GHz Amplifier
YouTube video will followDesigned for 50ohm impedance, 0.8mm thickness board requiredBoard tested to...
-
SiTime Clock Oscillators
I made these boards 0.8mm thick. Do not load R5 and R6.
-
LM399 10.000V Voltage Standard
Here are the youtube videos
-
Lorenz Attractor
From Paul Horowitz, the Lorenz attractor for oscilloscope XY display. YouTube video will follow late...
-
Zener Diode Tester
Jumper settings for 5, 10, 15, and 20mA currents
-
Dual and Quad OpAmp SImple Tester
here is a video explaining the board
-
NE5532 Headphone Amplifier
Popular op-amps are NE5532 JRC5532 NJM5532 you might consider JRC4556 for higher currents
-
Linear Optocoupler
note: pin one of the IC's are square pads, load correctly as they point different directions.
-
I2C 6 Digit Nixie Tube Display
Here is YouTube video, note this is part 5 of a series. You might want to watch all five.
-
Gyrator Board
circuits from: https://sound-au.com/articles/gyrator-filters.htm
-
Transistor Training PC Board
youtube video will follow soonPlease don't ask for a BOM or schematic. The board IS the schematic. I...
-
LCR Meter PCB Fixture
Made for an LCR meter with kelvin 4 BNC fixtures. this is standard spacing of 22mm between connector...
You may also like
-
-
-
-
-
3D printed Enclosure Backplate for Riden RD60xx power supplies
162 1 1 -
-
