Description
SMD to SIP adapter boards
Note: these are REV B boards that fix any problems shown in the YouTube video.
Note: when you order these boards. leave a note the board includes vgrooves, and there is a Gerber layer 'Vgroove'
Use pins: Digikey and Mouser: TE Connectivity AMP Connectors 1544210-2
Aug 04,2024
790 views
SMD to SIP adapter boards
several version for different packages
790
6
4
Published: Aug 04,2024
Download Gerber file 53
PCBWay Donate 10% cost To Author
*PCBWay community is a sharing platform. We are not responsible for any design issues and parameter issues (board thickness, surface finish, etc.) you choose.
Under the
Attribution-ShareAlike (CC BY-SA)
License.
Topic
- Comments(4)
- Likes(6)
Upload photo
You can only upload 5 files in total. Each file cannot exceed 2MB. Supports JPG, JPEG, GIF, PNG, BMP
0 / 10000
More by IMSAIGUY
-
Op-amp Test Board
This is a two section board. two dual op-amps can be compared. Half of the device is used in a non-i...
-
Panaplex Display Board
this project is documented on YouTube
-
ATTINY ETC board for ETW-3800 Microprocessor Trainer
this board fits the Heathkit ETW-3800 trainer. it has I2C breakout chips to allow lots of IO to conn...
-
Narrow SO-20 to DIP Adapter
this results in a 0.300" DIP for protoboardsit also includes a spot for a bypass capacitor to be use...
-
Narrow SO-16 to DIP Adapter
the DIP has a 0.300" size for protoboard maximization
-
Tiny IMSAI 8080 Computer
This uses an ATTINY814 microcontroller and a bunch of 74595 shift registers to flash the LEDs and re...
-
Narrow SO-14 SMD to DIP Adapter
I made this for using Attiny414 814 type devices on a protoboard with only 0.3" of width
-
Digital Capacitor Bandpass Filter
uses PE64012 serial programmable digital capacitorhttps://youtu.be/zgKv5fhoEHI
-
Mini-Circuits MAR MMIC Amplifier
When ordering board, choose 0.8mm thickness. This is correct thickness for 50ohm transmission line.R...
-
Weinschel Programmable Attenuator
YouTube video series describes project
-
Electrical Symbol Drafting Stencil
I wanted a drafting template for use with a Micron 08 pen. I had this made with 2.5mm thick clear ac...
-
MiniCircuits GVA-63+ 6GHz Amplifier
This amp is part of a YouTube series from start to finish, It is 10 parts. Here are parts 1 and 10
-
SMD to SIP adapter boards
Note: these are REV B boards that fix any problems shown in the YouTube video.Note: when you order t...
-
Chua's Circuit
YouTube video will followhttps://en.wikipedia.org/wiki/Chua%27s_circuitAnalyzing the circuit using K...
-
MGA-82563 6GHz Amplifier
YouTube video will followDesigned for 50ohm impedance, 0.8mm thickness board requiredBoard tested to...
-
SiTime Clock Oscillators
I made these boards 0.8mm thick. Do not load R5 and R6.
-
LM399 10.000V Voltage Standard
Here are the youtube videos
-
Lorenz Attractor
From Paul Horowitz, the Lorenz attractor for oscilloscope XY display. YouTube video will follow late...
You may also like
-
MPL3115A2 Barometric Pressure, Altitude, and Temperature Sensor
46 0 0 -
-
-
V2 Commodore AMIGA USB-C Power Sink Delivery High Efficiency Supply Triple Output 5V ±12V OLED display ATARI compatible shark 100W
261 4 1 -
How to measure weight with Load Cell and HX711
375 0 3 -
-
Instrumentation Input, high impedance with 16 bit 1MSPS ADC for SPI
504 0 0
