Description
Chua's Circuit
YouTube video will follow
https://en.wikipedia.org/wiki/Chua%27s_circuit
Analyzing the circuit using Kirchhoff's circuit laws, the dynamics of Chua's circuit can be accurately modeled by means of a system of three nonlinear ordinary differential equations in the variables x(t), y(t), and z(t), which represent the voltages across the capacitors C1 and C2 and the electric current in the inductor L1 respectively.[5] These equations are:
,
Jul 04,2024
964 views
end-flag
Chua's Circuit
Chua's circuit (also known as a Chua circuit) is a simple electronic circuit that exhibits classic chaotic behavior.
964
2
1
Published: Jul 04,2024
Download Gerber file 32
PCBWay Donate 10% cost To Author
*PCBWay community is a sharing platform. We are not responsible for any design issues and parameter issues (board thickness, surface finish, etc.) you choose.
Under the
Attribution-ShareAlike (CC BY-SA)
License.
Raspberry Pi 5 7 Inch Touch Screen IPS 1024x600 HD LCD HDMI-compatible Display for RPI 4B 3B+ OPI 5 AIDA64 PC Secondary Screen（Without Speaker）
BUY NOW
ESP32-S3 4.3inch Capacitive Touch Display Development Board, 800×480, 5-point Touch, 32-bit LX7 Dual-core Processor
BUY NOW
Raspberry Pi 5 7 Inch Touch Screen IPS 1024x600 HD LCD HDMI-compatible Display for RPI 4B 3B+ OPI 5 AIDA64 PC Secondary Screen（Without Speaker）
BUY NOW
Topic
- Comments(1)
- Likes(2)
Log in to post comments.
Upload photo
0 / 10000
Reply
More by IMSAIGUY
-
MiniCircuits GVA-63+ 6GHz Amplifier
This amp is part of a YouTube series from start to finish, It is 10 parts. Here are parts 1 and 10
-
SMD to SIP adapter boards
Note: these are REV B boards that fix any problems shown in the YouTube video.Note: when you order t...
-
Chua's Circuit
YouTube video will followhttps://en.wikipedia.org/wiki/Chua%27s_circuitAnalyzing the circuit using K...
-
MGA-82563 6GHz Amplifier
YouTube video will followDesigned for 50ohm impedance, 0.8mm thickness board requiredBoard tested to...
-
SiTime Clock Oscillators
I made these boards 0.8mm thick. Do not load R5 and R6.
-
LM399 10.000V Voltage Standard
Here are the youtube videos
-
Op-amp Test Board
This is a two section board. two dual op-amps can be compared. Half of the device is used in a non-i...
-
Small Gear Motor Housing
YouTube video will followThis is a 3D print file for a housing/mount for small gear motors. the moto...
-
Panaplex Display Board
this project is documented on YouTube
-
ATTINY ETC board for ETW-3800 Microprocessor Trainer
this board fits the Heathkit ETW-3800 trainer. it has I2C breakout chips to allow lots of IO to conn...
-
Narrow SO-20 to DIP Adapter
this results in a 0.300" DIP for protoboardsit also includes a spot for a bypass capacitor to be use...
-
Narrow SO-16 to DIP Adapter
the DIP has a 0.300" size for protoboard maximization
-
Tiny IMSAI 8080 Computer
This uses an ATTINY814 microcontroller and a bunch of 74595 shift registers to flash the LEDs and re...
-
Narrow SO-14 SMD to DIP Adapter
I made this for using Attiny414 814 type devices on a protoboard with only 0.3" of width
-
Digital Capacitor Bandpass Filter
uses PE64012 serial programmable digital capacitorhttps://youtu.be/zgKv5fhoEHI
-
Mini-Circuits MAR MMIC Amplifier
When ordering board, choose 0.8mm thickness. This is correct thickness for 50ohm transmission line.R...
-
Weinschel Programmable Attenuator
YouTube video series describes project
-
Electrical Symbol Drafting Stencil
I wanted a drafting template for use with a Micron 08 pen. I had this made with 2.5mm thick clear ac...
-
MiniCircuits GVA-63+ 6GHz Amplifier
This amp is part of a YouTube series from start to finish, It is 10 parts. Here are parts 1 and 10
-
SMD to SIP adapter boards
Note: these are REV B boards that fix any problems shown in the YouTube video.Note: when you order t...
-
Chua's Circuit
YouTube video will followhttps://en.wikipedia.org/wiki/Chua%27s_circuitAnalyzing the circuit using K...
-
MGA-82563 6GHz Amplifier
YouTube video will followDesigned for 50ohm impedance, 0.8mm thickness board requiredBoard tested to...
-
SiTime Clock Oscillators
I made these boards 0.8mm thick. Do not load R5 and R6.
-
LM399 10.000V Voltage Standard
Here are the youtube videos
-
Op-amp Test Board
This is a two section board. two dual op-amps can be compared. Half of the device is used in a non-i...
-
Small Gear Motor Housing
YouTube video will followThis is a 3D print file for a housing/mount for small gear motors. the moto...
-
Panaplex Display Board
this project is documented on YouTube
-
ATTINY ETC board for ETW-3800 Microprocessor Trainer
this board fits the Heathkit ETW-3800 trainer. it has I2C breakout chips to allow lots of IO to conn...
-
Narrow SO-20 to DIP Adapter
this results in a 0.300" DIP for protoboardsit also includes a spot for a bypass capacitor to be use...
-
Narrow SO-16 to DIP Adapter
the DIP has a 0.300" size for protoboard maximization
You may also like
-
-
-
Commodore 64 1541-II 1581 Floppy Disk Drive C64 Power Supply Unit USB-C 5V 12V DIN connector 5.25
449 1 4 -
-
-
-
-
-
-
Modifying a Hotplate to a Reflow Solder Station
1298 1 6 -
MPL3115A2 Barometric Pressure, Altitude, and Temperature Sensor
729 0 1
