Preamplificatore AjeanMos a simmetria complementare
Questo preamplificatore è progettato a simmetria complementare.
Il differenziale si compone di una doppia coppia di BC,
la scelta può essere fatta fra
BC546 BC556 sia selezione B che C
BC547 BC557 sia selezione B che C
BC550 BC560 sia selezione B che C
Un buon match dei componenti del differenziale vi garantirà una minore DC di uscita.
Il preamplificatore è molto trasparente e ha un guadagno di 11x.
I due trimmer servono per regolare la tensione di alimentazione in un range compreso fra circa 28 e 40 volt,
questo vi concede un pò di liberta sulla scelta del trasformatore, tenendo a mente che gli stabilizzatori di alimentazione hanno un droop di tensione di circa 3v.
Per aumentare il voltaggio un trimmer gira in senso orario e l'altro in senso antiorario.
Allego anche il modello del supporto del preamplificatore stampabile in 3D.
Preamplificatore AjeanMos a simmetria complementare
*PCBWay community is a shared platform and we are not responsible for any design issues.
- Comments(0)
- Likes(0)
- 0 USER VOTES
- YOUR VOTE 0.00 0.00
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- Amplifier MX5OnisA (THE BLAMELESS AMPLIFIER CONCEPT) Questa versione di amplificatore è molto simile al "THE BLAMELESS AMPLIFIER CONCEPT"http://www.dougl...
- Amplifier LoniTip100 Questo amplificatore è il 2° della linea LoniTip100ha una potenza di 100w rmsalimentazione +-45vrego...
- Amplifier Loni Tip50 Questo amplificatore, il più piccolo LoniTip50ha una potenza di 50w rmsalimentazione +-35vregolazion...
- Preamplificatore AjeanMos a simmetria complementare Questo preamplificatore è progettato a simmetria complementare.Il differenziale si compone di una do...
- ProtoDac DileOnisA TDA1387 x8 R2R DAC a calibrazione continua, per Raspberry This is a new version of the Protodac. Different from the original only in terms of layout. The dac-...
- Lonisino Class AB 50w amplifier Lonisino project,a simple amplifier with good performance.Through the videos you can see all the ste...
- The gainclone LM3875 The Gainclone LM3875https://phonoclone.com/diy-gc.html
- Preamplifier RagnaMos 1.5 This preamplifier is built around a small MOSFET, the BS170. The current source is composed of a JFE...
- LM1875 high current +TIP35+TIP36 This amplifier is based on the LM1875 integrated circuit, which respectively drives a TIP35 and a TI...
- LM3875 Amplifier This amplifier is based on the LM3875. The signal ground has been separated from the GND, and a high...
-
MLight: Compact All-in-One Control Board for Soldering Tools
11 0 0 -
SMD version - Bluetooth Module Supply and Booster board for tube radio
45 0 0 -
-
-
-
Digispark DIY: Open-Source ATtiny85 USB Arduino PCB Design Files
87 0 2 -
2.4GHz receiver circuit using ESP32, nRF24L01 with IC motor controller L298N
72 0 0 -
Somei70 keyboard PCB - 70 key alternative layout
65 0 1 -