RGB LED Stairlight
This is my new stairlight with RGB-LEDs. Motion-Sensor on top and bottom of the stairs to autoswitch on and off.
The code recognizes movement direction and use the pir on the opposit side to switch off after short delay.
This Project is made for Home Assistant, but you can write your own code for NodeMCU as well.
PIN-Usage:
D1: Status-LED PIR top
D2: Status-LED PIR down
D5: PIR bottom
D6: RGB-LED
D7: PIR top
D8: Status-LED lightlevel
(In v1.0 the bottom PIR was on D8. This causes the esp not to boot up. So I switched the Pins D5 and D8. If you have the v1.0 use RX or another free Data-Pin for PIR)
v1.2 fixes the missing GND connection of the RGB-LED connector
Sourcecodes:
All Codes for ESPHome and Home Assistant automations are on my manual-page (german) at:
https://smarthomeyourself.de/rgb-treppe
Video:
RGB LED Stairlight
*PCBWay community is a sharing platform. We are not responsible for any design issues and parameter issues (board thickness, surface finish, etc.) you choose.
- Comments(0)
- Likes(7)
- 4 USER VOTES
- YOUR VOTE 0.00 0.00
-
1design
-
10usability
-
10creativity
-
10content
-
10design
-
10usability
-
10creativity
-
10content
-
10design
-
10usability
-
10creativity
-
10content
-
1design
-
5usability
-
3creativity
-
2content
More by Daniel Scheidler
-
Solar Einspeise-Regelung
Cooperation between UTUBERLARS and SmartHome yourself.This PCB is designed to switch the output volt...
-
Barcode scanner made for ESPHome
The project was created to fill my shoppinglist by scanning ean/gtin codes.All project informations ...
-
Neopixel-Ring RGB Clock (with ESPHome for Home Assistant)
RGB-Clock with ESPHome for Home Assistant.Use Neopixel-Ring with 60 LEDs to show current Time.To dis...
-
Smart Garage-Door control with animated RGB-LED (with or without Home Assistant)
Standalone:automated RGB-LED-Animation when door is opening / closingAdditional features when using ...
-
FPV Laptime Tracker
The Project is to track laptimes of FPV Racing Drones in races. No modification of the FPV Copter is...
-
Integrate every doorbell in Home Assistant
This PCB was designed to integrate my old doorbell into Home Assistant.The board uses the transforme...
-
RGB LED Ambiente light
Panel with 3 PCBs of my ambience rgb led light with on/off- and color-switch button.More Details abo...
-
RGB LED Stairlight
This is my new stairlight with RGB-LEDs. Motion-Sensor on top and bottom of the stairs to autoswitch...
-
8 in 1 Sensor for Home Assistant
This PCB is an 8 in 1 Sensor for Home Assistant. The NodeMCU is flashed with ESPHome with the follow...
-
12V RGB Stripe Controller WiFi (for Home Assistant / ESPHome)
This PCB is designed to control non-adressable RGB-LED-Stripes in Home Assistant with ESPHome. Full ...
-
RF to MQTT Bridge for Home Assistant
THIS PCB SEEMS TO BE UNSTABLE! Will NOT be continuedPCB for OpenMQTTGateway as RF to MQTT Bridge for...
-
LED-stairlight (without fade) by SmartHome yourself
This PCB is for my motion-controlled stairlight. This PCB is desigend for up to 16 stair steps.Motio...
-
LED-stairlight (with fade) by SmartHome yourself
This PCB is for my motion-controlled stairlight. This PCB is desigend for up to 16 stair steps.Motio...
-
-
-
kmMiniSchield MIDI I/O - IN/OUT/THROUGH MIDI extension for kmMidiMini
110 0 0 -
DIY Laser Power Meter with Arduino
162 0 2 -
-
Box & Bolt, 3D Printed Cardboard Crafting Tools
153 0 2 -
A DIY Soldering Station Perfect for Learning (Floppy Soldering Station 3.0)
554 0 2
