10x10 SSOP PROTOTYPE BOARD Rev.A
A prototype board for lots of SMD components.
When prototyping these days is not easy to just get a bread board and plug things in. Surface mount packages requires breadboard adapters to be used. On the internet usually I only find QFP or SOIC to DIP adapters where all pins are routed to the border headers. Everybody building circuits know that not all pins are going to be used and that decoupling capacitors are better to be put as closed to the IC as possible.
I designed this board taking all that in consideration and much more.
The board is designed based on the standard 100x100mm surface and using two layer design.
This board is part of a series of boards that I am sharing with you all sharing the same basic layout in order to help with mix an match as needed.
Now for the details:
The board is split into four quadrants and there are some guide lines to help you cut it if you need.
This prototype board has different areas that can accommodate different chips:
- One SSOP-44 0.5mm pitch
- Two SOIC-10 1mm pitch
- One SOP-32 1.27mm pitch
- One SOP-44 0.5mm pitch
- Two SSOP-28 0.635mm pitch
- Two USOP-8 0.635mm pitch
- One TSOP-48 0.5mm pitch wide
- One SSOP-48 0.635mm pitch
- SSOP-36 0.65mm pitch wide
- SSOP-16 0.65mm pitch
- TSOP-44 0.8mm pitch wide
- multiple single line headers are mounted in different places on the board. They can be used for connectors or to mount any other daughter card on top of bellow. These resemble the IF word.
- Plenty of pads are left unconnected for soldering passive components as: SMD resistors, capacitors, diodes, etc. SMD transistors can be soldered on diagonal using three pads. This allows you to wire the circuit as needed and you can build the whole prototype with no need to use adapters and bread boards.
- The pads are extended to the edges to allow for soldering of dual line header connectors.
And that is not all. If your project is not big enough to use the entire area then look for small lines that I put in specific places which will allow you to easily score and cut the board in smaller and still usable prototype boards. These small boards can be stack up on each other as needed
If your project do not fit on this board then use two of them and stack them up. There is a reason why the IC pins are not wired directly to any of the trough hole pads.
There is still more I can talk about this board capabilities and as this is meant as a prototype board use your imagination and make it yours.
check out the others boards I am sharing as many of them follows the same pattern and allows you to bring your prototype to the next level.
Looking forward to improve the design. If you have any improvements that you would like me to consider please leave a comment bellow.
10x10 SSOP PROTOTYPE BOARD Rev.A
*PCBWay community is a sharing platform. We are not responsible for any design issues and parameter issues (board thickness, surface finish, etc.) you choose.
- Comments(0)
- Likes(3)
More by Florin Muntean
-
10x10 SMD PROTO Rev.C
As I am building a FPGA based computer I have designed another prototype board for SMD components.On...
-
10x10_ESP_PROTOBOARD_Rev.C
ESP protoboard rev.BThis a prototype board for using with ESP8266, ESP32, and ESP32-S2 modules.The b...
-
ESP protoboard rev.A
This a prototype board for using with ESP8266 and ESP32 modules.The board is split into multiple are...
-
10x10 QFP PROTOTYPE BOARD Rev.A
A prototype board for lots of SMD components.When prototyping these days is not easy to just get a b...
-
10x10 SSOP PROTOTYPE BOARD Rev.A
A prototype board for lots of SMD components.When prototyping these days is not easy to just get a b...
-
QFP64 to DIP 0.8mm Rev.A
This is a prototype board that support QFP ICs with 32, 48, 64 pins with a 0.8mm pitch.On the intern...
-
SMD Prototype PCB Rev.B
A prototype board for SMD components.On the internet usually only find QFP or SOIC to DIP adapters w...
-
10x10 ProtoBoard
A prototype board for lots of SMD components.On the internet usually only find QFP or SOIC to DIP ad...
-
QFP144 to DIP adaptor 2
This is a prototype board that support QFP ICs with 32, 48, 64, 80, 100, 144 pins with a 0.5mm pitch...
-
-
-
-
kmMiniSchield MIDI I/O - IN/OUT/THROUGH MIDI extension for kmMidiMini
140 0 0 -
DIY Laser Power Meter with Arduino
214 0 2 -
-
Box & Bolt, 3D Printed Cardboard Crafting Tools
186 0 2
