DIY 4017 CLAP SWITCH CIRCUIT.
THIS IS A SIMPLE CLAP SWITCH CCIRCUIT THAT USES A 4017ic DECODER. WHEN U CLAP ONCE, IT TURNS THE RELAY ON AND WHEN U CLAP AGAIN ,IT SWITCHES OFF. SINCE THIS CIRCIT USES A RELAY, U CAN CONNECT IT TO ANY DOMESTIC ELECTRONIC APPLIANCE DEPENDING ON THE RELAY'S amp LIMIT.
THIS CIRCUIT CAN USE A REGULAR 2 PIN ELECTRET MICROPHONE OR A MICROPHONE MODULE.(MAKE SURE THAT U ONLY USE ONE OF THEM).
ALL U GOTTA DO IS JUSTSOLDER THE COMPONENTS TO THE RELEVENT PLACE
YOU WILL NEED: IC 4017, 220Ω RESISTOR (2), 680Ω RESISTORS(2), 47K RESISTOR, 1K RESISTOR, BC547 TRANSISTOR (3), LEDS (GREEN,RED), 5V RELAY, MALE PIN HEADERS, 3 PIN SCREW PIN HEADERS AND A LOT OF LEAD :)
THE VIDEO BELOW IS NOT MINE BUT I FU WANT TO KNOW MORE ABOUT THIS IC THEN IT'S BETTER IF U WATCH IT :)
pls like my project :)
DIY 4017 CLAP SWITCH CIRCUIT.
*PCBWay community is a sharing platform. We are not responsible for any design issues and parameter issues (board thickness, surface finish, etc.) you choose.
- Comments(4)
- Likes(3)
- gnanam Jul 12,2019
- rachman bobo Feb 04,2019
- umar_khalid Dec 01,2018
- 2 USER VOTES
- YOUR VOTE 0.00 0.00
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
-
2design
-
7usability
-
10creativity
-
1content
-
1design
-
1usability
-
1creativity
-
1content
More by umar_khalid
- DIY ARDUINO UNO BOARD this is a regular arduino board which all u need to do is solder the components and use a (FT232RL) ...
- ARDUINO IR CONTROLLED RELAY (AC/DC) This circuit needs maximum 5v - 7v if powered directly through DC power supply only. If ur supplyi...
- LIGHT AND MOTION SENSITIVE LAMP CIRCUIT This is a circuit which activates a RELAY when the envoiroment is dark and when there is a movement ...
- DIY ARDUINO PRO MINI 2.0 (upgraded version) This is a DIY arduino PRO mini which is like a regular arduino pro minni but it has less components ...
- DIY SMD ARDUINO UNO This is a regular arduino board which contains extra features such as an extra VCC/GND rail and it u...
- DIY SMD ARDUINO UNO R3 This is a regular arduino board which contains extra features such as an extra VCC/GND rail and it u...
- LDR CONTROLLED RELAY MODULE SMD This is a simple LDR dark sensor project which is designed to turn ON a relay (when there is light) ...
- DIY ARDUINO UNO SHEILD SMD This is a simple arduino sheild that can run on it's own as an arduino uno once it's powered...
- DIY arduino UNO sheild This is a simple arduino sheild that can run on it's own as an arduino uno once it's powered...
- DIY 4017 CLAP SWITCH CIRCUIT. THIS IS A SIMPLE CLAP SWITCH CCIRCUIT THAT USES A 4017ic DECODER. WHEN U CLAP ONCE, IT TURNS THE R...
- DIY DIGITAL CLOCK THIS IS A SIMPLE DIGITAL CLOCK THAT WORKS WITH A 9V BATTERY AND CAN BE SET JUST THREE BUTTONS.IF U L...
- DIY ARDUINO UNO R3 SMD THIS WORKS AS A REGULAR ARDUINO UNO WITH AN SMD ATMEGA 328P.U JUST NEED TO SOLDER THE COMPONENTS AND...
- arduino mega password security system shield this is a sheild for an arduino mega. this security system can be accesed using RFID and IR and a ke...
- LED CHASER this is a simple circuit using an ic 4017 and an ic 555 timer . u can adjust the frequency using the...
- LED CHASER this is a simple circuit using an ic 4017 and an ic 555 timer . u can adjust the frequency using the...
- DIY arduino uno r3 DIY arduino uno circuit.its used just like a regular arduino uno all u gotta do is get the component...
- ARDUINO UNO R3 AN ARDUINO UNO R3 DIY PROJECTU WILL NEED: ATmega 328P, 22PF ceramic capacitors(3), a few female pin ...
- 2 WAY INTERCOM CIRCUIT_20181119155207 THIS IS A 2 WAY INTERCOM CIRCUIT, IT WORKS LIKE A WALKIE TALKIE BUTWITH WIRES
-
-
-
kmMiniSchield MIDI I/O - IN/OUT/THROUGH MIDI extension for kmMidiMini
125 0 0 -
DIY Laser Power Meter with Arduino
182 0 2 -
-
-
Box & Bolt, 3D Printed Cardboard Crafting Tools
165 0 2 -