Soft start for LED (max current 2A) or Arduino load control (max current 2A)
### DESCRIPTION
Board for soft-srart led strip 12V or 24V
Have 1 pin control (Cntr) when positive voltage is applied to it, the N-ch mosfet is opened and the tape of the plan flares up when the voltage is worn, the tape is gradually fade. if there is no possibility of separate control, the pins + and Cntr are to be sealed together, then there will only be a smooth flares up
another application of this board:
Load control by means of arduiono. To do this, instead of resistors R1 and R2, solder one resistor 100Ω to the lower pins R1 and R2 and additionally solder the resistor R4 with 10 kΩ
### TECHNICAL DETAILS / COMPONENTS
For soft-start:
- sot23 N-ch Mosfet ( for exemple AO3400)
- R1 - 0805 resistor 68KΩ
- R2 - 0805 resistor 10KΩ
- R3 - 0805 resistor 51KΩ
- R4 - not used
- C1 - Ceramic or Tantalum capasitor 22uf or more ( the more capacity the longer the LED lights up)
To control the load using arduino:
- sot23 N-ch Mosfet ( for exemple AO3400)
- to the bottom of the pins of the resistors R! and R2 - 0805 resistor 100Ω
- R4 - 0805 resistor 10KΩ
### LEARN / TOPIC / BUILD INSTRUCTIONS
Soft start for LED (max current 2A) or Arduino load control (max current 2A)
*PCBWay community is a sharing platform. We are not responsible for any design issues and parameter issues (board thickness, surface finish, etc.) you choose.
- Comments(0)
- Likes(0)
- 0 USER VOTES
- YOUR VOTE 0.00 0.00
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
More by Максим Maxbolt
- Christmas toy from MaX Simple PCB for a Christmas moodMarry Christmas!
- Christmas tree 2019 NeoPixels WS2812B Attiny13 ### DESCRIPTIONChristmas tree as a decoration of the desktop, can be connected via USB power. Pleasa...
- Led lamp T10 or W5W for car ### DESCRIPTIONCar lamp t10 or W5W. Of the features - no polarity, installation by either side, adde...
- TP4056 Linear Li-ion cnarger 3A or othrer (0,4A - 4A) ### DESCRIPTIONThis board is designed to charge 1 li-ion battery with 3A current performed on TP4056...
- Soft start for LED (max current 2A) or Arduino load control (max current 2A) ### DESCRIPTIONBoard for soft-srart led strip 12V or 24VHave 1 pin control (Cntr) when positive volt...
- Test board 16-channel led driver DM631 (12bit PWM control) ### DESCRIPTIONA test card for debugging the firmware on Arduino or learning the capabilities of thi...
-
-
-
3D printed Enclosure Backplate for Riden RD60xx power supplies
55 0 0 -
-
-
-
Sega Master System RGB Encoder Switcher Z80 QSB v1.2
57 0 0 -
18650 2S2P Battery Charger, Protection and 5V Output Board
78 0 0 -
High Precision Thermal Imager + Infrared Thermometer | OpenTemp
420 0 6 -
Sony PlayStation Multi Output Frequency Oscillator (MOFO) v1
129 0 2