Note: For eagle the latest version 9.6.2, please click How to Generate Gerber and Drill Files From Eagle 9.6.2

Generally it doesn't work to use the Eagle files for PCB manufacturing , so the situation will be better if you can send the Gerber files directly to a PCB fab. In this tutorial, we are going to show you how to export Gerber files from your eagle .brd file, then you can upload it to PCBWay online system for fabrication.

*If you are using the lastest version of Eagle software ( Eagle 9.20 or higher ), please take a reference of THIS POST.*

Before generating Gerber files from Eagle, firstly you need to confirm the silkscreen is on single side or double sides, because only the top silkscreen layer (tPlace and tNames) would be generated by default in Eagle software. When your PCB has double sides silkscreen, you need to add the bottom layer as well (Dimension, bPlace and bName). If there is any milling design in your brd file, please add extra outline layer and check the"Dimension" /span> "Milling". After following the 4 steps you will have all the necessary files needed for PCB manufacturing.

1. Generating Drill Files

To create a Gerber file in Eagle, you should run the drillcfg command first:

File -->Run ULP -->  the pop-up "Drill Configuration" dialog box and click the "OK" button to generate the corresponding drill configuration file.

Open the .brd file, and then click the "File" menu to open the "CAM Processor" dialog box.

In the "CAM Processor" dialog box, select "File" -> "Open" -> "Job ..." command, open the "Open CAM Job" dialog box, select the "excellentone.cam" and click "Open" button.

After loading it, click the "Process Job" command to generate the corresponding drill file:

2. Generating Gerber Files

In the "CAM Processor" dialog box, select "File" -> "Open" -> "Job ..." command, open the "Open CAM Job" dialog box, select one of the "gerb274x.cam" and click "Open" After it is loaded, click the "Process Job" command to generate the corresponding Gerber file:

Please note: When it is the double layers silkscreen of your PCB, you need to add the bottom layer as well in the CAM Processor (20 Dimension,22 bPlace and 26 bNames).

Click "Add" --> Change Section to something like “Silkscreen bl”-- > Change File to “%N.pls”--> Deselect all layers --> Select layers 20 Dimension, 22 bPlace and 26 bNames

If there is any milling design in your brd file, please add extra outline layer and check the "20 Dimension" and "46 Milling".

Click "Add" --> Change Section to something like “Edge cut outline”-- > Change File to “%N.gko”--> Deselect all layers --> Select layers 20 Dimension and 46 milling.

After completing the above steps, in your. brd file where the directory will generate some other documents --- Gerber files ,which can be sent to the PCB manufacturers to produce.

But before you upload the Gerber files to PCBWay online system or other manufacturing fab, you should always check all the layers and look at them using a Gerber viewer to make sure everything is ok.

The following files that you should now have in your Gerber file :

*.cmp (Copper, component side)

*.drd (Drill file)

*.dri (Drill Station Info File) – Usually not needed

*.gpi (Photoplotter Info File) – Usually not needed

*.plc (Silk screen, component side)

*.pls (Silk screen, solder side)

*.sol (Copper, solder side)

*.stc (Solder stop mask, component side)

*.sts (Solder stop mask, solder side)

3. Compress all the files in a single .zip file

The final step is to Compress all the files in a single .zip file, then you can fill out the form about your PCB parameters ( size, quantity , layers , thickness , etc ) on our “PCB Instant quote” page and upload your .zip ( Gerber ) file to PCBWay online system, our engineers will check it again and feedback to you if any problems happen before it can be fabricated. Here we go!

You can also download our CAM file to export Gerber files directly in Eagle software and avoid any problem :

PCBWay_2 layer.cam

PCBWay_4 layer.cam

PCBWay_6 layer.cam