4 inch 480x320 TFT Display v1.1
4.0 inch 480x320 TFT Display v1.1
Display source
This is a 4 inch ILI9488 320x480 display module that uses a 12 pin 1mm pitch FFC connector. The 12 pin connector, which handles both the display and touchscreen controller, can be mounted horizontally or vertically as needed. This board’s footprint is smaller horizontally than the widely available ILI9488 320x480 display modules. This board also fixes an issue with many of the display modules where the display doesn’t release MISO making sharing the SPI bus with the touchscreen controller and other SPI devices impossible.
The jumpers SJ1, SJ2 and SJ3 are jumpered to allow the display and touchscreen to use the same SPI bus.
If needed the board can be configured so that the touchscreen controller uses a different SPI bus by using a separate 4 pin FFC connector for the controller. In this case the jumpers SJ1, SJ2 and SJ3 are left untouched/not jumpered.
JP3 is a 4 pin, 1mm pitch, bottom contact, FFC connector source. Note that JP3 is only installed when you want to run the touchscreen controller on a separate SPI bus.
U1 is a XPT2046 touch controller chip. source
The buffer chip, U2, is optionally installed only when you need to be able to read from the display. In most cases you only need to write to the display so U2 and C5 can be omitted. This chip is used to release MOSI when the display chip select goes high/unselected.
JP1, JP2 are 12 pin, 1mm pitch, bottom contact, FFC connectors source. You only need to install JP1 or JP2, not both. When built for my Dust Collector Monitor v4 project use JP1, the connector closest to the 40 pin display connector.
A1 is a 40 pin, 0.5mm pitch, upper contact, FFC connector source. Note that the quality of these connectors varies based on the vendor. Try to locate connectors that are wrapped with metal on both ends. The low quality versions only provide a metal pad and tend to break very easily.
To attach the display to the board I use 3 horizontal strips of 10mm double sided tape. source
This board can be used with my breadboard adapter here
This board is used in my Dust Collector Monitor v4 project here
4 inch 480x320 TFT Display v1.1
*PCBWay community is a sharing platform. We are not responsible for any design issues and parameter issues (board thickness, surface finish, etc.) you choose.
- Comments(0)
- Likes(2)
- Carlos Vargas Oct 14,2024
- Engineer Jul 15,2023
- 0 USER VOTES
- YOUR VOTE 0.00 0.00
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
More by Jonnathan Mackey
- STM32F103RE 3 Axis CNC v1 See my Instructable for a full implementation example here.All end stops, stepper driver fault lines...
- PT226x Remote v1.1 This is a remote encoder board that supports several versions of PT226x encoder chips in a number of...
- Dust Collector Monitor v4 This is the 4th version of my dust collector monitor. See my instructable for a full description of ...
- 3.5 inch 480x320 TFT Display v1.1 3.5 inch 480x320 TFT Display v1.1Display sourceThis is a 3.5 inch ILI9488 320x480 display module tha...
- 4 inch 480x320 TFT Display v1.1 4.0 inch 480x320 TFT Display v1.1Display sourceThis is a 4 inch ILI9488 320x480 display module that ...
- 12 pin FFC Display Adaptor v1.0 12 pin FFC Display Adaptor v1.0This is a breadboard adapter for use with my boards that have a 12 pi...
- ILI9488 Display Adapter v1.0 ILI9488 Display Adapter v1.0This adapter board converts the 14 pin header found on many display modu...
- Heating System Monitor This board is used to monitor the heating system in your home by reflecting the state of the alarm t...
- 4G LTE TempSensor v1.2 (SIM7000) This board is used to monitor multiple temperature sensors and report out of range conditions to you...
- 4 Port RJ11 4P4C v1.0 This board is part of a multi board project used to monitor multiple temperature sensors and report ...
- BMP280 RFM69CW Remote See my instructable for a full description of this board and the associated software.Part of my hiki...
- RFM69 3 Button Remote See my instructable for a full description of this board and the associated software.Remote control ...
- Hiking Data Logger Using RFM69CW This hiking data logger is used to record a hike’s location, start and end time, temperature, altitu...
- AVR SD Hex Loader ISP v1.4 This project is all about getting your compiled sketch onto your target board without the need to ha...
- Blast Gate Sensor This is a blast gate sensor board. This uses a 49E Hall sensor to determine if a gate is open or clo...
- Dust Collector Monitor This is a dust collector monitor board. Both the dust bin level and the filter are monitored. When e...
- AVR SD Hex Loader ISP See my instructable for a full description of this board and the associated software.Note that there...
- 5 Button Board This is a simple 5 button board. It can be used with a 2x3 2.54 header OR a 6 pin 1mm pitch FFC conn...
-
-
-
kmMiniSchield MIDI I/O - IN/OUT/THROUGH MIDI extension for kmMidiMini
121 0 0 -
DIY Laser Power Meter with Arduino
172 0 2 -
-
-
Box & Bolt, 3D Printed Cardboard Crafting Tools
162 0 2 -