Tools, APP Software Used etc.
|
EagleAutodesk
|
Description
Guitar Pedal Switcher
Guitar pedal switch matrix. turn on and off pedals, connect in any order. This is a project in the works. It uses analog MUX chips controlled by a Atmega328P chip. code at: https://github.com/imsaiguy/Guitar-Pedal-Switch
Schematic and Layout
Schematic
switch.sch
Layout
switch.brd
Aug 23,2021
4,436 views
end-flag
Guitar Pedal Switcher
Guitar pedal switch matrix. turn on and off pedals, connect in any order
4436
4
4
10.00 (1)
Published: Aug 23,2021
Download Gerber file 74
BOM(Bill of materials)
Centroid file
PCBWay Donate 10% cost To Author
File Last Updated: 2024/02/29 (GMT+8)
File update record
2024-02-2910:37:25
Centroid file is updated.
2024-02-2910:37:25
Parts List (BOM) is updated.
*PCBWay community is a sharing platform. We are not responsible for any design issues and parameter issues (board thickness, surface finish, etc.) you choose.
Under the
Attribution-ShareAlike (CC BY-SA)
License.
Raspberry Pi 5 7 Inch Touch Screen IPS 1024x600 HD LCD HDMI-compatible Display for RPI 4B 3B+ OPI 5 AIDA64 PC Secondary Screen（Without Speaker）
BUY NOW
ESP32-S3 4.3inch Capacitive Touch Display Development Board, 800×480, 5-point Touch, 32-bit LX7 Dual-core Processor
BUY NOW
Raspberry Pi 5 7 Inch Touch Screen IPS 1024x600 HD LCD HDMI-compatible Display for RPI 4B 3B+ OPI 5 AIDA64 PC Secondary Screen（Without Speaker）
BUY NOW
Topic
- Comments(4)
- Likes(4)
VOTING
1 votes
- 1 USER VOTES
10.00
- YOUR VOTE 0.00 0.00
-
10design
-
10usability
-
10creativity
-
10content
10.00
More by IMSAIGUY
-
SMD to SIP adapter boards
Note: these are REV B boards that fix any problems shown in the YouTube video.Note: when you order t...
-
Chua's Circuit
YouTube video will followhttps://en.wikipedia.org/wiki/Chua%27s_circuitAnalyzing the circuit using K...
-
MGA-82563 6GHz Amplifier
YouTube video will followDesigned for 50ohm impedance, 0.8mm thickness board requiredBoard tested to...
-
SiTime Clock Oscillators
I made these boards 0.8mm thick. Do not load R5 and R6.
-
LM399 10.000V Voltage Standard
Here are the youtube videos
-
Lorenz Attractor
From Paul Horowitz, the Lorenz attractor for oscilloscope XY display. YouTube video will follow late...
-
Op-amp Test Board
This is a two section board. two dual op-amps can be compared. Half of the device is used in a non-i...
-
Panaplex Display Board
this project is documented on YouTube
-
ATTINY ETC board for ETW-3800 Microprocessor Trainer
this board fits the Heathkit ETW-3800 trainer. it has I2C breakout chips to allow lots of IO to conn...
-
Narrow SO-20 to DIP Adapter
this results in a 0.300" DIP for protoboardsit also includes a spot for a bypass capacitor to be use...
-
Narrow SO-16 to DIP Adapter
the DIP has a 0.300" size for protoboard maximization
-
Tiny IMSAI 8080 Computer
This uses an ATTINY814 microcontroller and a bunch of 74595 shift registers to flash the LEDs and re...
-
Narrow SO-14 SMD to DIP Adapter
I made this for using Attiny414 814 type devices on a protoboard with only 0.3" of width
-
Digital Capacitor Bandpass Filter
uses PE64012 serial programmable digital capacitorhttps://youtu.be/zgKv5fhoEHI
-
Mini-Circuits MAR MMIC Amplifier
When ordering board, choose 0.8mm thickness. This is correct thickness for 50ohm transmission line.R...
-
Weinschel Programmable Attenuator
YouTube video series describes project
-
Electrical Symbol Drafting Stencil
I wanted a drafting template for use with a Micron 08 pen. I had this made with 2.5mm thick clear ac...
-
MiniCircuits GVA-63+ 6GHz Amplifier
This amp is part of a YouTube series from start to finish, It is 10 parts. Here are parts 1 and 10
-
SMD to SIP adapter boards
Note: these are REV B boards that fix any problems shown in the YouTube video.Note: when you order t...
-
Chua's Circuit
YouTube video will followhttps://en.wikipedia.org/wiki/Chua%27s_circuitAnalyzing the circuit using K...
-
MGA-82563 6GHz Amplifier
YouTube video will followDesigned for 50ohm impedance, 0.8mm thickness board requiredBoard tested to...
-
SiTime Clock Oscillators
I made these boards 0.8mm thick. Do not load R5 and R6.
-
LM399 10.000V Voltage Standard
Here are the youtube videos
-
Lorenz Attractor
From Paul Horowitz, the Lorenz attractor for oscilloscope XY display. YouTube video will follow late...
-
Op-amp Test Board
This is a two section board. two dual op-amps can be compared. Half of the device is used in a non-i...
-
Panaplex Display Board
this project is documented on YouTube
-
ATTINY ETC board for ETW-3800 Microprocessor Trainer
this board fits the Heathkit ETW-3800 trainer. it has I2C breakout chips to allow lots of IO to conn...
-
Narrow SO-20 to DIP Adapter
this results in a 0.300" DIP for protoboardsit also includes a spot for a bypass capacitor to be use...
-
Narrow SO-16 to DIP Adapter
the DIP has a 0.300" size for protoboard maximization
-
Tiny IMSAI 8080 Computer
This uses an ATTINY814 microcontroller and a bunch of 74595 shift registers to flash the LEDs and re...
You may also like
-
-
-
Modifying a Hotplate to a Reflow Solder Station
950 1 6 -
MPL3115A2 Barometric Pressure, Altitude, and Temperature Sensor
480 0 1 -
-
-
V2 Commodore AMIGA USB-C Power Sink Delivery High Efficiency Supply Triple Output 5V ±12V OLED display ATARI compatible shark 100W
1188 4 2 -
How to measure weight with Load Cell and HX711
736 0 3
added a link in description