Fabio Battaglia
ITALY • + Follow
Description
MSP-MDC Redux
This board is a reverse-engineered recreation of the CPU/Security module for the Wink arcade game (1985, by Midcoin).
Midcoin placed the CPU and address scrambling logic for the Arcade board on 3 PCBs encased in epoxy, to dissuade bootleggers from copy their game.
If a component inside this block dies, the whole board becomes useless.
I painstakingly pulled the board apart, and removed enough epoxy to rebuild the original circuit. This reimplementation is plug-and-play: just remove the old dead board and install this one.
Find the repository here: https://github.com/hkzlab/WINK_MSP-MDC_redux
Schematic and Layout
Schematic, BOM, Gerbers and layout
https://github.com/hkzlab/WINK_MSP-MDC_redux
Aug 22,2024
277 views
end-flag
MSP-MDC Redux
Reimplementation of the MSP-MDC CPU/Security module for the Wink arcade board by Midcoin
277
0
0
Published: Aug 22,2024
Download Gerber file 1
PCBWay Donate 10% cost To Author
*PCBWay community is a sharing platform. We are not responsible for any design issues and parameter issues (board thickness, surface finish, etc.) you choose.
Under the
Attribution-ShareAlike (CC BY-SA)
License.
Raspberry Pi 5 7 Inch Touch Screen IPS 1024x600 HD LCD HDMI-compatible Display for RPI 4B 3B+ OPI 5 AIDA64 PC Secondary Screen（Without Speaker）
BUY NOW
ESP32-S3 4.3inch Capacitive Touch Display Development Board, 800×480, 5-point Touch, 32-bit LX7 Dual-core Processor
BUY NOW
Raspberry Pi 5 7 Inch Touch Screen IPS 1024x600 HD LCD HDMI-compatible Display for RPI 4B 3B+ OPI 5 AIDA64 PC Secondary Screen（Without Speaker）
BUY NOW
- Comments(0)
- Likes(0)
Log in to post comments.
Upload photo
0 / 10000
More by Fabio Battaglia
-
8x8 LED MATRIX EDUBOARD
This board is an educational implementation of an 8x8 multiplexed led matrix. The rows/columns bits ...
-
dupico - EPROM_01 POD
The EPROM_01 POD is an adapter for the DuPAL V3 (AKA "dupico") meant to support the most common 24/2...
-
MSP-MDC Redux
This board is a reverse-engineered recreation of the CPU/Security module for the Wink arcade game (1...
-
dupico - PAL POD
The PAL POD is an adapter for the DuPAL V3 (AKA "dupico") meant to support 20 and 24 pin PAL (and pi...
-
DuPAL V3 - dupico
The DuPAL V3, AKA "dupico" board is a simple circuit that mounts a Raspberry Pico (RP2040), 74HC595 ...
-
SCART SyncSplitter
This card takes an RGB + Composite signal from a SCART connector and outputs the same RGB signal + s...
-
PlayStation PU-22 8MB RAM daughterboard
This daughterboard replaces the RAM IC on PU-22 PlayStation motherboards, allowing the user to expan...
-
MiniPerformer+
This board is a remix of the Micromac Performer reversed by Bolle, resized for installation on the M...
-
The Padapter
This board converts a SEGA MegaDrive/Genesis 3-button gamepad for C64 (and similar)/Amiga use.All bu...
-
Commodore C128 (310381 R7) SRAM Adapter
This board implements a static RAM replacement for the DRAMs on a C128 with a 310381R7 motherboard.Y...
-
Angled 44 pin 2.0mm pitch adapter
I was in need of fitting a uSD to IDE adapter inside a cramped case, the connector for it was horizo...
-
Lava RSC Lite Famiclone Upgrade board
The Lava RSC is a family of very nice Famiclones that use ICs found in the original Famicom, complem...
-
A500 IDE LED mod board
This board reproduces the same circuit that the A500 uses to flash the "DRIVE" LED when the /MTR0 si...
-
C64 250407 SRAM Adapter
This board implements a static RAM replacement for the DRAMs on a C64 with a 250407 motherboard. I w...
-
8x8 LED MATRIX EDUBOARD
This board is an educational implementation of an 8x8 multiplexed led matrix. The rows/columns bits ...
-
dupico - EPROM_01 POD
The EPROM_01 POD is an adapter for the DuPAL V3 (AKA "dupico") meant to support the most common 24/2...
-
MSP-MDC Redux
This board is a reverse-engineered recreation of the CPU/Security module for the Wink arcade game (1...
-
dupico - PAL POD
The PAL POD is an adapter for the DuPAL V3 (AKA "dupico") meant to support 20 and 24 pin PAL (and pi...
-
DuPAL V3 - dupico
The DuPAL V3, AKA "dupico" board is a simple circuit that mounts a Raspberry Pico (RP2040), 74HC595 ...
-
SCART SyncSplitter
This card takes an RGB + Composite signal from a SCART connector and outputs the same RGB signal + s...
-
PlayStation PU-22 8MB RAM daughterboard
This daughterboard replaces the RAM IC on PU-22 PlayStation motherboards, allowing the user to expan...
-
MiniPerformer+
This board is a remix of the Micromac Performer reversed by Bolle, resized for installation on the M...
-
The Padapter
This board converts a SEGA MegaDrive/Genesis 3-button gamepad for C64 (and similar)/Amiga use.All bu...
-
Commodore C128 (310381 R7) SRAM Adapter
This board implements a static RAM replacement for the DRAMs on a C128 with a 310381R7 motherboard.Y...
-
Angled 44 pin 2.0mm pitch adapter
I was in need of fitting a uSD to IDE adapter inside a cramped case, the connector for it was horizo...
-
Lava RSC Lite Famiclone Upgrade board
The Lava RSC is a family of very nice Famiclones that use ICs found in the original Famicom, complem...
You may also like
-
-
Commodore 64 1541-II 1581 Floppy Disk Drive C64 Power Supply Unit USB-C 5V 12V DIN connector 5.25
315 1 3 -
Easy to print simple stacking organizer with drawers
113 0 0 -
-
-
-
-
-
Modifying a Hotplate to a Reflow Solder Station
1209 1 6 -
MPL3115A2 Barometric Pressure, Altitude, and Temperature Sensor
690 0 1 -
